enow.com Web Search

  1. Ads

    related to: 2 foot diameter drainage pipe home depot 4 inch

Search results

  1. Results from the WOW.Com Content Network
  2. Nominal Pipe Size - Wikipedia

    en.wikipedia.org/wiki/Nominal_Pipe_Size

    Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

  3. Drain-waste-vent system - Wikipedia

    en.wikipedia.org/wiki/Drain-waste-vent_system

    Older structures may use asbestos, copper, iron, lead or clay pipes, in rough order of era of use. Under many older building codes, a vent stack (a pipe leading to the main roof vent) is required to be within approx. a 5-foot (1.5 m) radius of the draining fixture it serves (sink, toilet, shower stall, etc.). [2]

  4. Orangeburg pipe - Wikipedia

    en.wikipedia.org/wiki/Orangeburg_pipe

    Orangeburg pipe (also known as "fiber conduit", "bituminous fiber pipe" or "Bermico" or "sand pipe") is bituminized fiber pipe used in the United States. It is made from layers of ground wood pulp fibers and asbestos fibres compressed with and bound by a water resistant adhesive then impregnated with liquefied coal tar pitch .

  5. Garden hose - Wikipedia

    en.wikipedia.org/wiki/Garden_hose

    This fitting is used with 1 ⁄ 2-inch, 5 ⁄ 8-inch, and 3 ⁄ 4-inch hoses. [4] [5] In other countries, a British Standard Pipe (BSP) thread is used, which is 3 ⁄ 4 inch (19 mm) and 14 TPI (male part outside diameter is 26.441 mm or 1.04 in). The GHT and BSP standards are not compatible, and attempting to connect a GHT hose to a BSP fitting ...

  6. Culvert - Wikipedia

    en.wikipedia.org/wiki/Culvert

    As the diameter of the reline pipe will be smaller than the host pipe, the cross-sectional flow area will be smaller. By selecting a reline pipe with a very smooth internal surface with an approximate Hazen-Williams Friction Factor C value of between 140–150, the decreased flow area can be offset, and hydraulic flow rates potentially ...

  7. Sanitary sewer - Wikipedia

    en.wikipedia.org/wiki/Sanitary_sewer

    Most of the solids are removed by the septic tanks, so the treatment plant can be much smaller than a typical plant. In addition, because of the vast reduction in solid waste, a pumping system, rather than a gravity system, can be used to move the wastewater. The pipes have small diameters, typically 1.5 to 4 inches (4 to 10 cm).

  8. Plumbing - Wikipedia

    en.wikipedia.org/wiki/Plumbing

    [28] 1/2" L copper has the same outer diameter as 1/2" K or M copper. The same applies to pipe schedules. As a result, a slight increase in pressure losses is realized due to a decrease in flowpath as wall thickness is increased. In other words, 1 foot of 1/2" L copper has slightly less volume than 1 foot of 1/2 M copper. [29]

  9. Iron pipe size - Wikipedia

    en.wikipedia.org/wiki/Iron_pipe_size

    During the IPS period, pipes were cast in halves and welded together, and pipe sizes referred to the inside diameters. [1] The inside diameters under IPS were roughly the same as the more modern Ductile Iron Pipe Standard (DIPS) and Nominal Pipe Size (NPS) Standards, and some of the wall thicknesses were also retained with a different ...

  1. Ads

    related to: 2 foot diameter drainage pipe home depot 4 inch