enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Float shifting - Wikipedia

   en.wikipedia.org/wiki/Float_shifting

   Float shifting can reduce clutch wear because it is used so much less (only for starting from a standstill). Conversely, improper engagement of a gear (when the engine and transmission speeds aren't matched) can cause wear on the synchros and lockouts, and damage the gears by physically grinding them together due to a difference in speed.

3. Dana 60 - Wikipedia

   en.wikipedia.org/wiki/Dana_60

   Dana 61 axle tag showing 3.73:1 ratio [1] The Dana 61 was made in semi-float and full-float axles for select 4×2 and 4x4 Ford 3 ⁄ 4-ton and 1 Ton Pickups and Vans from 1974 to 1987. A Dana 61 front axle was selectively used in Dodge 4×4 3 ⁄ 4-ton and 1 Ton pickups from 1987 to 1993. Although 3.07:1 and 3.31:1 gear sets are common for a ...

4. Close-ratio transmission - Wikipedia

   en.wikipedia.org/wiki/Close-ratio_transmission

   The designation of wide versus close ratio affected the lowest gear ratio; [7] for example, the four-speed Muncie transmissions offered in General Motors performance vehicles included the M20 "wide ratio" transmission, which had a first gear ratio of 2.52 or 2.56:1, while the M21 and M22 "close ratio" transmissions had a first gear ratio of 2. ...

5. GM 4L60-E transmission - Wikipedia

   en.wikipedia.org/wiki/GM_4L60-E_transmission

   The police package (9C1) B-body cars featured a First Gear Block Out (FGBO) Plate on the transmission housing to prevent drivetrain damage. The shift point for first to second gear is about 43 MPH (69 km/h) while second to third gear shift point is about 83 MPH (134 km/h) assuming a 3.08:1 differential and a 5,500 RPM engine speed limit.

6. Dana 70 - Wikipedia

   en.wikipedia.org/wiki/Dana_70

   The Dana 70 axle only came with 5.13:1, 4.88,5.31 [citation needed] gear ratios and had a GAWR of [citation needed] these axles were rated at 7-9klbs as seen on 5500 door stickers. They differ greatly from previous Dana 70 front axles, some of the major differences being the use of 1550 Universal Joints and being a high pinion, reverse cut axle.

7. Non-synchronous transmission - Wikipedia

   en.wikipedia.org/wiki/Non-synchronous_transmission

   Three-speed sliding-gear non-synchronous transmission Non-synchronous "crash" gearbox; commonly used today in semi-trucks and tractors, and formerly used in automobiles pre-1950s. A non-synchronous transmission, also called a crash gearbox, is a form of manual transmission based on gears that do not use synchronizing mechanisms. They require ...

8. Comparison of hub gears - Wikipedia

   en.wikipedia.org/wiki/Comparison_of_hub_gears

   5th gear 1550-2040 g City Shimano Nexus Inter-7: 1995 7 244% 1465-1860 g City Shimano Nexus Inter-5E 2019 5 263% 60 Nm 1st gear 1650 g e-bike Shimano Nexus 4 Speed 4 184% 1st gear City Shimano Nexus Inter-3: 3 187% 2nd gear 1220 g City SRAM Spectro E12 (Elan) 1995 1999 12 339% 3500-4000 g City SRAM i-Motion 9: 2005 2012 9 340% 2000g (w/o brake)-

9. Tremec TR-6060 transmission - Wikipedia

   en.wikipedia.org/wiki/Tremec_TR-6060_transmission

   As usual, the forward helical cut gears are synchronized. However, the reverse gear operates through a fully synchronized constant-mesh system. The TR-6060 contains removable wear pads on the shift forks, and uses aluminum alloys for the main case, extension housing, and clutch housing.