enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. Chevrolet small-block engine (first- and second-generation)

    en.wikipedia.org/wiki/Chevrolet_small-block...

    This block is one of three displacements, 302/327/350, that underwent a crankshaft bearing diameter transformation for 1968 when the rod-journal size was increased from the 2 in (50.8 mm) diameter small-journal to a 2.1 in (53.3 mm) large-journal and a main-journal size that was increased from 2.3 in (58.4 mm) to 2.45 in (62.2 mm).

  3. Chevrolet small-block engine - Wikipedia

    en.wikipedia.org/wiki/Chevrolet_small-block_engine

    The Chevrolet small-block engine refers to one of the several gasoline-powered vehicle engines manufactured by General Motors. These include: The first or second generation of non-LS Chevrolet small-block engines; The third, fourth, or fifth generation of LS-based GM engines; The Chevrolet Gemini small-block engine

  4. Nissan RB engine - Wikipedia

    en.wikipedia.org/wiki/Nissan_RB_engine

    There are many stroker kits available for RB Engines (some only available as proper kits while others being achievable by using cranks from other engines, for example a GT-R crank, pistons and rods in an RB25DET will make its displacement 2.6L as the Bore is the same as an RB26DETT). Achievable Stroker Displacements for RB Engines: RB20 - 2.2, 2.4

  5. General Motors LS-based small-block engine - Wikipedia

    en.wikipedia.org/wiki/General_Motors_LS-based...

    The LS4 is adapted for transverse front-wheel drive applications, with a bellhousing bolt pattern that differs from the rear-wheel-drive blocks (so as to mate with the 4T65E). According to GM, "the crankshaft is shortened 13–3 mm (0.51–0.12 in) at the flywheel end and 10 mm (0.39 in) at the accessory drive end – to reduce the length of ...

  6. Shrink-fitting - Wikipedia

    en.wikipedia.org/wiki/Shrink-fitting

    Shrink-fitting is a technique in which an interference fit is achieved by a relative size change after assembly. This is usually achieved by heating or cooling one component before assembly and allowing it to return to the ambient temperature after assembly, employing the phenomenon of thermal expansion to make a joint. For example, the thermal ...

  7. Mitsubishi Astron engine - Wikipedia

    en.wikipedia.org/wiki/Mitsubishi_Astron_engine

    The SOHC eight-valve 4G54 (also known as the G54B) displaces 2.6 L (2,555 cc), with bore & stroke at 91.1 mm × 98 mm (3.59 in × 3.86 in). The G54B for the US market had a cylinder head with additional jet valves to improve emissions (MCA-Jet system).

  8. Stroke ratio - Wikipedia

    en.wikipedia.org/wiki/Stroke_ratio

    Since the stroke is significantly longer than the bore, the SOHC 16V (2-valve per cylinder) version of this engine is able to generate a peak torque of 350 lb·ft as low as 2501 rpm. The Willys Jeep L134 and F134 engines were undersquare, with a bore and stroke of 79.4 mm × 111.1 mm (3.13 in × 4.37 in) stroke (bore/stroke ratio = 0.714:1).

  9. GM Family II engine - Wikipedia

    en.wikipedia.org/wiki/GM_Family_II_engine

    The Family II is a straight-4 piston engine that was originally developed by Opel in the 1970s, debuting in 1981. Available in a wide range of cubic capacities ranging from 1598 to 2405 cc, it simultaneously replaced the Opel CIH and Vauxhall Slant-4 engines, and was GM Europe's core mid-sized powerplant design for much of the 1980s, and provided the basis for the later Ecotec series of ...