enow.com Web Search

  1. Ads

    related to: standard drawer sizes in mm height measurements guide

Search results

  1. Results from the WOW.Com Content Network
  2. Rack unit - Wikipedia

    en.wikipedia.org/wiki/Rack_unit

    Rack with sample component sizes including an A/V half-rack unit. A rack unit (abbreviated U or RU) is a unit of measure defined as 1 + 3 ⁄ 4 inches (44.45 mm). [1] [2] It is most frequently used as a measurement of the overall height of 19-inch and 23-inch rack frames, as well as the height of equipment that mounts in these frames, whereby the height of the frame or equipment is expressed ...

  3. 19-inch rack - Wikipedia

    en.wikipedia.org/wiki/19-inch_rack

    The size denotes the width of the faceplate for the installed equipment. The rack unit is a measure of vertical spacing and is common to both the 19 and 23-inch racks. Hole spacing is either on 1-inch (25 mm) centers (Western Electric standard), or the same as for 19-inch (482.6 mm) racks (0.625 in or 15.9 mm spacing).

  4. 32 mm cabinetmaking system - Wikipedia

    en.wikipedia.org/wiki/32_mm_cabinetmaking_system

    A typical 5 mm shelf stud may measure 15-16 mm long, and has a thin flange of about 7 mm diameter halfway at its length. Distance of the front row of holes to the front edge: 37 mm The system includes matching fittings, with which furniture sides can be secured to floors, walls, and adjacent cabinets.

  5. Filing cabinet - Wikipedia

    en.wikipedia.org/wiki/Filing_cabinet

    Lateral files are typically 20 inches (510 mm) deep and manufactured in 30,-36,-and-42-inch (760, 910, and 1,070 mm) widths and 2-, 3-, 4-, and 5-drawer versions. The 30-inch-wide (760 mm), two-drawer version is popular for use inside cubicle workstations, as it is engineered to fit under or alongside the cubicle work surfaces.

  6. International Standard Payload Rack - Wikipedia

    en.wikipedia.org/wiki/International_Standard...

    The rack has internal mounting provisions to allow attachment of secondary structure. The ISPRs will be outfitted with a thin center post to accommodate sub-rack-sized payloads, such as the 483 mm (19-inch rack) Spacelab Standard Interface Rack (SIR) Drawer or the Space Shuttle Middeck Locker. Utility pass-through ports are located on each side ...

  7. List of disk drive form factors - Wikipedia

    en.wikipedia.org/wiki/List_of_disk_drive_form...

    4 in × 1 in × 5.75 in (101.6 mm × 25.4 mm × 146 mm) = 376.77344 cm³. This smaller form factor is similar to that used in an HDD by Rodime in 1983, which was the same size as the "half height" 3½" FDD, i.e., 1.63 inches high. Today, the 1-inch high ("slimline" or "low-profile") version of this form factor is the most popular form used in ...

  8. AOL Mail

    mail.aol.com

    Get AOL Mail for FREE! Manage your email like never before with travel, photo & document views. Personalize your inbox with themes & tabs. You've Got Mail!

  9. Eurocard (printed circuit board) - Wikipedia

    en.wikipedia.org/wiki/Eurocard_(printed_circuit...

    Eurocard is an IEEE standard format for printed circuit board (PCB) cards that can be plugged together into a standard chassis which, in turn, can be mounted in a 19-inch rack. The chassis consists of a series of slotted card guides on the top and bottom, into which the cards are slid so they stand on end, like books on a shelf.

  1. Ads

    related to: standard drawer sizes in mm height measurements guide