enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. Drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    So a 1 / 2 in (12.7 mm) diameter drill will be able to drill a hole 4 + 1 / 2 in (114.3 mm) deep, since it is 9 times the diameter in length. A 1 / 8 in (3.175 mm) diameter drill can drill a hole 1 + 5 / 8 in (41.275 mm) deep, since it is 13 times the diameter in flute length.

  3. Orders of magnitude (length) - Wikipedia

    en.wikipedia.org/wiki/Orders_of_magnitude_(length)

    To help compare different orders of magnitude, this section lists lengths between 10 −3 m and 102 m (1 mm and 1 cm). 1.0 mm1/1,000 of a meter; 1.0 mm – 0.03937 inches or 5/127 (exactly) 1.0 mm – side of a square of area 1 mm²; 1.0 mm – diameter of a pinhead; 1.5 mm – average length of a flea [27]

  4. List of rail transport modelling scale standards - Wikipedia

    en.wikipedia.org/wiki/List_of_rail_transport...

    Lego trains use a fixed nominal gauge of 37.5 mm (1 + 15 ⁄ 32 in), based on 5-stud track centerlines gauge. [5] [6] [7] The 37.5 mm length is not derived by a certain scale ratio. While HO scale is a 1:87 scale (3.5 mm to 1 foot), resulting in a 16.5 mm (0.65 in) gauge from real life prototype 1,435 mm (4 ft 8 + 12 in) standard gauge ...

  5. Mesh (scale) - Wikipedia

    en.wikipedia.org/wiki/Mesh_(scale)

    Although such information contains long lists of sieve sizes, in practice sieves are normally used in series in which each member sieve is selected to pass particles approximately 1/ √ 2 smaller in diameter or 1/2 smaller in cross-sectional area than the previous sieve. For example the series 80mm, 63, 40, 31.5, 20, 16, 14, 10, 8, 6.3, 4, 2.8 ...

  6. Unified Thread Standard - Wikipedia

    en.wikipedia.org/wiki/Unified_Thread_Standard

    The standard designation for a UTS thread is a number indicating the nominal (major) diameter of the thread, followed by the pitch measured in threads per inch.For diameters smaller than1 / 4 ⁠ inch, the diameter is indicated by an integer number defined in the standard; for all other diameters, the inch figure is given.

  7. List of unusual units of measurement - Wikipedia

    en.wikipedia.org/wiki/List_of_unusual_units_of...

    In radio astronomy, the unit of electromagnetic flux is the jansky (symbol Jy), equivalent to 10 −26 watts per square metre per hertz (= 10 −26 kg/s 2 in base units, about 8.8×10 −31 BTU/ft 2). It is named after the pioneering radio astronomer Karl Jansky. The brightest natural radio sources have flux densities of the order of one to one ...

  8. Millimetre - Wikipedia

    en.wikipedia.org/wiki/Millimetre

    Different lengths as in respect to the electromagnetic spectrum, measured by the metre and its derived scales.The microwave is between 1 meter to 1 millimeter.. The millimetre (international spelling; SI unit symbol mm) or millimeter (American spelling) is a unit of length in the International System of Units (SI), equal to one thousandth of a metre, which is the SI base unit of length.

  9. Visual acuity - Wikipedia

    en.wikipedia.org/wiki/Visual_acuity

    For 6/6 = 1.0 acuity, the size of a letter on the Snellen chart or Landolt C chart is a visual angle of 5 arc minutes (1 arc min = 1/60 of a degree), which is a 43 point font at 20 feet. [10] By the design of a typical optotype (like a Snellen E or a Landolt C), the critical gap that needs to be resolved is 1/5 this value, i.e., 1 arc min.