enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. Honda K engine - Wikipedia

    en.wikipedia.org/wiki/Honda_K_engine

    The Honda K-series engine is a line of four-cylinder four-stroke car engines introduced in 2001. The K-series engines are equipped with DOHC valvetrains and use roller rockers on the cylinder head to reduce friction. The engines use a coil-on-plug, distributorless ignition system with a coil for each spark plug. This system forgoes the use of a ...

  3. Acura TSX - Wikipedia

    en.wikipedia.org/wiki/Acura_TSX

    The engine is a 2.4-liter in-line 4-cylinder engine reaching 201 hp (150 kW) and 172 lb⋅ft (233 N⋅m) torque. [25] While the rated power of the new TSX engine is 4 hp (3.0 kW) lower than that of the 2008 model, Acura says the new engine distributes power across a much wider rpm range, which along with the increased torque, provides an ...

  4. List of GE reciprocating engines - Wikipedia

    en.wikipedia.org/wiki/List_of_GE_reciprocating...

    GE GEVO-12, 12-cylinder engine used in locomotives, such as the GE ES30ACi, GE ES44AC, [6] GE ES43ACi, GE ES43ACmi, 3TE25K2M and MPI HSP46 Diesel Locomotives; GE GEVO-16, 16-cylinder engine used in locomotives, such as the GE ES59ACi, [6] GE ES58ACi, [6] GE ES57ACi Diesel Locomotives. HDL series [1] GE 7HDL-16, 16-cylinder engine used in only ...

  5. Chrysler 2.2 & 2.5 engine - Wikipedia

    en.wikipedia.org/wiki/Chrysler_2.2_&_2.5_engine

    The first version of this engine family was a normally aspirated 2.2 L (134 cu in) unit. Developed under the leadership of Chief Engineer – Engine Design and Development Willem Weertman and head of performance tuning Charles "Pete" Hagenbuch, who had worked on most of Chrysler's V-8 engines and the Chrysler Slant-6 engine, [1] it was introduced in the 1981 Dodge Aries, Dodge Omni, Plymouth ...

  6. Austin D-Series engine - Wikipedia

    en.wikipedia.org/wiki/Austin_D-Series_engine

    All engines had a forged four main bearing crankshaft. [1] The engine was developed under the close watch of Austin chief Leonard Lord. The design was inspired by the Chevrolet Stovebolt engine, which was an inline six-cylinder used by General Motors' British subsidiary Bedford Vehicles. In the late 1930s, Austin decided to get into the 2-3 ton ...

  7. Rover KV6 engine - Wikipedia

    en.wikipedia.org/wiki/Rover_KV6_engine

    The engine was designed and developed by Rover at Longbridge to replace the Honda 2.7l V6 engine which was about to become non-compliant with tightening emissions legislation. The original unit was designed for low volume production but was later redesigned to fit into the smaller Rover 75 's bonnet, although performance remained similar.

  8. Nissan CA engine - Wikipedia

    en.wikipedia.org/wiki/Nissan_CA_engine

    The engine was deemed too expensive to produce due to its cast-iron block, while it also no longer met the ever-changing Japanese emission standards emerging at the time. The 1.8 L and 2.0 L versions were replaced by the all-aluminium SR series as Nissan's primary four-cylinder engine, while the smaller 1.6 L version was replaced by the GA series.

  9. Cleveland Diesel Engine Division - Wikipedia

    en.wikipedia.org/wiki/Cleveland_Diesel_Engine...

    The engines operates on the 2-stroke cycle principle, are air started, and are rated at 1600 bhp at 756 rpm on the 16-248 and 750 rpm on the 16-278A. The size of the bore and stroke of the 16-248 engine is 8 + 1 ⁄ 2 inches and 10 + 1 ⁄ 2 inches respectively as compared to 8 + 3 ⁄ 4 inches and 10 + 1 ⁄ 2 inches for Model 16-278A.