enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Plastic pipework - Wikipedia

   en.wikipedia.org/wiki/Plastic_pipework

   Pipes, fittings, valves, and accessories make up a plastic pressure pipe system. The range of pipe diameters for each pipe system does vary. However, the size ranges from 12 to 400 mm (0.472 to 15.748 in) and 3 ⁄ 8 to 16 in (9.53 to 406.40 mm). Pipes are extruded and are generally available in: 3 m (9.84 ft), 4 m (13.12 ft), 5 m (16.40 ft ...

3. Nominal Pipe Size - Wikipedia

   en.wikipedia.org/wiki/Nominal_Pipe_Size

   Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

4. Drain-waste-vent system - Wikipedia

   en.wikipedia.org/wiki/Drain-waste-vent_system

   All DWV systems require various sized fittings and pipes which are measured by their internal diameter of both the pipes and the fittings which, and in most cases are Schedule 40 PVC wye's, tee's, elbows ranging from 90 degrees to 22.5 degrees for both inside diameter fitment (street) as well as outer diameter fitment (hub), repair and slip ...

5. Sanitary sewer - Wikipedia

   en.wikipedia.org/wiki/Sanitary_sewer

   In addition, because of the vast reduction in solid waste, a pumping system, rather than a gravity system, can be used to move the wastewater. The pipes have small diameters, typically 1.5 to 4 inches (4 to 10 cm). Because the waste stream is pressurized, they can be laid just below the ground surface along the land's contour. [citation needed]

6. Piping and plumbing fitting - Wikipedia

   en.wikipedia.org/wiki/Piping_and_plumbing_fitting

   [19]: 71 The rubber sleeves are typically secured with stainless steel worm drive clamping bands, which compress the rubber to make a tight seal around the pipes and fittings. These pipe clamps are similar to hose clamps, but are heavier-duty and ideally are made completely of stainless steel (including the screw) to provide maximum service life.

7. Pipe (fluid conveyance) - Wikipedia

   en.wikipedia.org/wiki/Pipe_(fluid_conveyance)

   For pipe sizes of NPS 14 inch (DN 350) and greater the NPS size is the actual diameter in inches and the DN size is equal to NPS times 25 (not 25.4) rounded to a convenient multiple of 50. For example, NPS 14 has an OD of 14 inches or 355.60 millimetres, and is equivalent to DN 350.

8. Dollar General, Dollar Tree's consumers continue to tighten ...

   www.aol.com/finance/dollar-general-dollar-trees...

   Dollar Tree's same-store sales are up 1.8% from a year ago, beating the 1.38% expected, boosted by an increase in the average ticket and a 1.5% uptick in foot traffic. Its revenue of $7.56 billion ...

9. Fibre-reinforced plastic tanks and vessels - Wikipedia

   en.wikipedia.org/wiki/Fibre-reinforced_plastic...

   FRP tanks and vessels designed as per BS 4994 are widely used in the chemical industry in the following sectors: chlor-alkali manufacturers, fertilizer, wood pulp and paper, metal extraction, refining, electroplating, brine, vinegar, food processing, and in air pollution control equipment, especially at municipal waste water treatment plants and water treatment plants.