enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Fibre Channel - Wikipedia

   en.wikipedia.org/wiki/Fibre_Channel

   Fibre Channel started in 1988, with ANSI standard approval in 1994, to merge the benefits of multiple physical layer implementations including SCSI, HIPPI and ESCON. Fibre Channel was designed as a serial interface to overcome limitations of the SCSI and HIPPI physical-layer parallel-signal copper wire interfaces. Such interfaces face the ...

3. Optical Carrier transmission rates - Wikipedia

   en.wikipedia.org/wiki/Optical_Carrier...

   OC-48 is also used as a transmission speed for tributaries from OC-192 nodes in order to optimize card slot utilization where lower speed deployments are used. Slower cards that drop to OC-12, OC-3 or STS-1 speeds are more commonly found on OC-48 terminals, where use of these cards on an OC-192 terminal would not allow for full use of the ...

4. Fiber-optic cable - Wikipedia

   en.wikipedia.org/wiki/Fiber-optic_cable

   This is an accepted version of this page This is the latest accepted revision, reviewed on 19 January 2025. Cable assembly containing one or more optical fibers that are used to carry light A TOSLINK optical fiber cable with a clear jacket. These cables are used mainly for digital audio connections between devices. A fiber-optic cable, also known as an optical-fiber cable, is an assembly ...

5. Optical transport network - Wikipedia

   en.wikipedia.org/wiki/Optical_transport_network

   OTN was designed to provide higher throughput (currently 400G) than its predecessor SONET/SDH, which stops at 40 Gbit/s, per channel. ITU-T Recommendation G.709 is commonly called Optical Transport Network (OTN) (also called digital wrapper technology or optical channel wrapper). As of December 2009, OTN has standardized the following line rates.

6. Fibre Channel electrical interface - Wikipedia

   en.wikipedia.org/wiki/Fibre_Channel_electrical...

   Fibre channel input 29: GND (12V) 30 +OUT1: Fibre channel output 31-OUT1: Fibre channel output 32: GND (5V) 33 +OUT2: Fibre channel output 34-OUT2: Fibre channel output 35: GND (5V) 36: SEL2: Device ID bit 2 / ESI bit 2 37: SEL1: Device ID bit 1 / ESI bit 1 38: SEL0: Device ID bit 0 / ESI bit 0 39: DEVCTRL0: Input to control interface speed ...

7. Multi-mode optical fiber - Wikipedia

   en.wikipedia.org/wiki/Multi-mode_optical_fiber

   Optical fiber manufacturers have greatly refined their manufacturing process since that standard was issued and cables can be made that support 10 GbE up to 400 meters. Laser optimized multi-mode fiber (LOMMF) is designed for use with 850 nm VCSELs. Older FDDI grade, OM1, and OM2 fiber can be used for 10 Gigabit Ethernet through 10GBASE-LRM.

8. Fiber-optic communication - Wikipedia

   en.wikipedia.org/wiki/Fiber-optic_communication

   Fiber-optic communication is a form of optical communication for transmitting information from one place to another by sending pulses of infrared or visible light through an optical fiber. [ 1 ] [ 2 ] The light is a form of carrier wave that is modulated to carry information. [ 3 ]

9. Radio over fiber - Wikipedia

   en.wikipedia.org/wiki/Radio_over_fiber

   Electrical RF is directly connected to a TV or set-top box. 1550 nm is more popular because it has less losses in the fiber and by using fiber-optic amplifier known as EDFA it is possible to extend the transport distance. 1310 nm loses about 0.35 dB/km of optical signal, 1550 nm loses only 0.25 dB/km. Optical budget between transmitter and ...