enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Below is a comprehensive drill and tap size chart for all drills and taps: Inch, imperial, and metric, up to 36.5 millimetres (1.44 in) in diameter. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

  3. ISO metric screw thread - Wikipedia

    en.wikipedia.org/wiki/ISO_metric_screw_thread

    A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25). If the pitch is the normally used "coarse" pitch listed in ISO 261 or ...

  4. Unified Thread Standard - Wikipedia

    en.wikipedia.org/wiki/Unified_Thread_Standard

    To calculate the major diameter of "aught" size screws count the number of extra zeroes and multiply this number by 0.013 in and subtract from 0.060 in. For example, the major diameter of a #0000 screw is 0.060 in − (3 × 0.013 in) = 0.060 in − 0.039 in = 0.021 in.

  5. Screw thread - Wikipedia

    en.wikipedia.org/wiki/Screw_thread

    The nominal diameter of Metric (e.g. M8) and Unified (e.g. 5 ⁄ 16 in) threads is the theoretical major diameter of the male thread, which is truncated (diametrically) by 0.866 ⁄ 4 of the pitch from the dimension over the tips of the "fundamental" (sharp cornered) triangles.

  6. Metric drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    In the U.S., fractional inch and gauge drill bit sizes are in common use. In nearly all other countries, metric drill bit sizes are most common, and all others are anachronisms or are reserved for dealing with designs from the US. The British Standards on replacing gauge size drill bits with metric sizes in the UK was first published in 1959.

  7. List of thread standards - Wikipedia

    en.wikipedia.org/wiki/List_of_thread_standards

    Metric Screw Threads: M Profile: V Thread Form ASME B1.15-1995 (R2003) Unified Inch Screw Threads (UNJ Thread Form) V Thread Form ASME B1.20.1-2013: Pipe Threads, General Purpose (Inch) Pipe Thread Form ANSI B1.20.3-1976 (R2013) Dryseal Pipe Threads (Inch) Pipe Thread Form ASME B1.20.7-1991 (R2013) Hose Coupling Screw Threads - Inch: Pipe ...

  8. Width across flats - Wikipedia

    en.wikipedia.org/wiki/Width_across_flats

    The size is imprinted on the spanners in millimeter values or inch sizes with intermediate sizes in fractions (older British and current US spanners). The two systems are in general not compatible, which can result in rounding of nuts and bolts (i.e. using a 13 mm (0.51 in) spanner in place of a 1 ⁄ 2 inch (12.70 mm)).

  9. British Association screw threads - Wikipedia

    en.wikipedia.org/wiki/British_Association_screw...

    The thread angle is different from that used by Whitworth (55°), US Unified threads (60°) and ISO Metric (60°) so BA fasteners are not properly interchangeable with Whitworth or metric ones even when the pitch and diameter are similar enough that they can be screwed together (e.g., although 0BA appears similar to M6×1mm, the male and female ...