enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. Traditional French units of measurement - Wikipedia

    en.wikipedia.org/wiki/Traditional_French_units...

    Table of the measuring units used in the 17th century at Pernes-les-Fontaines in the covered market at Provence-Alpes-Côte d'Azur region of southeastern France. Although in the pre-revolutionary era (before 1795) France used a system and units of measure that had many of the characteristics of contemporary English units (or the later Imperial System of units), France still lacked a unified ...

  3. Medieval weights and measures - Wikipedia

    en.wikipedia.org/wiki/Medieval_weights_and_measures

    Linie – Line, usually 1 ⁄ 12 inch, but also 1 ⁄ 10. Zoll – Inch, usually 1 ⁄ 12 foot, but also 1 ⁄ 10. Fuss – Foot, varied between 23.51 cm in Wesel and 40.83 cm in Trier. Rheinfuss – Rhine foot, used in the North, 31.387 cm; Elle – Ell / cubit, distance between elbow and finger tip.

  4. Technical drawing tool - Wikipedia

    en.wikipedia.org/wiki/Technical_drawing_tool

    A scale ruler is a scaled, three-edged ruler which has six different scales marked to its sides. A typical combination for building details is 1:20, 1:50, 1:100, 1:25, 1:75 and 1:125. There are separate rulers for zoning work as well as for inch units. Today scale rulers are made of plastic, formerly they were made of hardwood. A pocket-sized ...

  5. Birmingham gauge - Wikipedia

    en.wikipedia.org/wiki/Birmingham_gauge

    The Birmingham gauge ranges from 5/0 or 00000, the lowest gauge number corresponding to the largest size of 0.500 inches (12.7 mm), to 36, the highest gauge number corresponding to the smallest size of 0.004 inches (0.10 mm). The increments between gauge sizes are not linear and vary. [2]

  6. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

  7. Angular diameter - Wikipedia

    en.wikipedia.org/wiki/Angular_diameter

    The angular diameter, angular size, apparent diameter, or apparent size is an angular separation (in units of angle) describing how large a sphere or circle appears from a given point of view. In the vision sciences , it is called the visual angle , and in optics , it is the angular aperture (of a lens ).

  8. Dots per inch - Wikipedia

    en.wikipedia.org/wiki/Dots_per_inch

    Actual size is approximately 1 ⁄ 4 by 1 ⁄ 4 inch (6 by 6 mm). Individual coloured droplets of ink are visible; this sample is about 150 DPI. Dots per inch (DPI, or dpi [1]) is a measure of spatial printing, video or image scanner dot density, in particular the number of individual dots that can be placed in a line within the span of 1 inch ...

  9. Orders of magnitude (length) - Wikipedia

    en.wikipedia.org/wiki/Orders_of_magnitude_(length)

    Typical size of a fog, mist, or cloud water droplet 10 μm Width of transistors in the Intel 4004, the world's first commercial microprocessor: 12 μm Width of acrylic fiber: 17-181 μm Width range of human hair [25] 10 −4: 100 μm: 340 μm Size of a pixel on a 17-inch monitor with a resolution of 1024×768 560 μm

  1. Related searches show 0.7 inches on a ruler map size

    show 0.7 inches on a ruler map size charthow to read inches on a ruler