enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   Below are some common spanner sizes for metric screw threads. Hexagonal (generally abbreviated to "hex") head widths (width across flats, spanner size) are for DIN 934 hex nuts and hex head bolts. Other (usually smaller) sizes may occur to reduce weight or cost, including the small series flange bolts defined in ISO 4162 which typically have ...

3. Preferred metric sizes - Wikipedia

   en.wikipedia.org/wiki/Preferred_metric_sizes

   A standard metric (concrete) block is 190 mm wide, 390 mm long, and 190 mm high, which allows for 10 mm mortar joints in between bricks, giving a standard unit size of 200 mm square by 400 mm long. [3] A standard metric brick is 90 by 57 by 190 mm; with 10 mm of mortar, that produces a standard unit of 100 mm x 200 mm. [3]

4. List of DIN standards - Wikipedia

   en.wikipedia.org/wiki/List_of_DIN_standards

   M42 to M160x6 hexagon head nuts; product grade B: Active: DIN 935-3: Hexagon slotted nuts with metric coarse pitch thread – Product grade C: Active: DIN 936: M8 to M52 and M8x1 to M52x3 hexagon thin nuts; product grades A and B: Withdrawn: DIN 937: Hexagon thin castle nuts: Withdrawn: DIN 938: Studs with a length of engagement equal to about ...

5. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   Metric Screw Threads: M Profile: V Thread Form ASME B1.15-1995 (R2003) Unified Inch Screw Threads (UNJ Thread Form) V Thread Form ASME B1.20.1-2013: Pipe Threads, General Purpose (Inch) Pipe Thread Form ANSI B1.20.3-1976 (R2013) Dryseal Pipe Threads (Inch) Pipe Thread Form ASME B1.20.7-1991 (R2013) Hose Coupling Screw Threads - Inch: Pipe ...

6. Width across flats - Wikipedia

   en.wikipedia.org/wiki/Width_across_flats

   Fastener terminology of hex nuts: d: Nominal thread diameter k: Wrench size (width across flats) h: Thickness e: Width across corners = Width across flats is the distance between two parallel surfaces on the head of a screw, bolt or nut. The width across flats will define the size of the spanner or wrench needed.

7. Screw - Wikipedia

   en.wikipedia.org/wiki/Screw

   Metric hex-headed lag screws are covered by DIN 571. Inch square-headed and hex-headed lag screws are covered by ASME B18.2.1. A typical lag screw can range in diameter from 4 to 20 mm or #10 to 1.25 in (4.83 to 31.75 mm), and lengths from 16 to 200 mm or 1 ⁄ 4 to 6 in (6.35 to 152.40 mm) or longer, with the coarse threads of a wood-screw or ...

8. ISO 898 - Wikipedia

   en.wikipedia.org/wiki/ISO_898

   ISO 898 is an international standard that defines mechanical and physical properties for metric fasteners. This standard is the origin for other standards that define properties for similar metric fasteners, such as SAE J1199 and ASTM F568M. [1] It is divided into five (nonconsecutive) parts: 1.

9. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   In 1913, Woolley and Meredith defined them like Anthony, but gave the following dimensions: hex head cap screws up to and including 7 ⁄ 16 inch (11.1125 mm) have a head that is 3 ⁄ 16 inch (4.7625 mm) larger than the shank diameter; screws greater than 1 ⁄ 2 inch (12.7 mm) in diameter have a head that is 1 ⁄ 4 inch (6.35 mm) larger than ...