enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Plywood - Wikipedia

   en.wikipedia.org/wiki/Plywood

   The most common dimension is 1.2 by 2.4 metres (3 ft 11 in × 7 ft 10 in) or the slightly larger imperial dimension of 4 feet × 8 feet. Plies vary in thickness from 1.4 mm to 4.3 mm. The number of plies—which is always odd—depends on the thickness and grade of the sheet. Roofing can use the thinner 16-millimetre (5 ⁄ 8 in) plywood ...

3. Board foot - Wikipedia

   en.wikipedia.org/wiki/Board_foot

   Note: see dimensional lumber for a full discussion of the relationship of actual and nominal dimensions. Briefly, for softwoods, to convert nominal to actual, subtract 1 ⁄ 4 inch (6 mm) for dimensions under 2 inches; subtract 1 ⁄ 2 inch (13 mm) for dimensions over 2 inches and under 8 inches; and subtract 3 ⁄ 4 inch (19 mm) for larger ...

4. Lumber - Wikipedia

   en.wikipedia.org/wiki/Lumber

   In 1961, at a meeting in Scottsdale, Arizona, the Committee on Grade Simplification and Standardization agreed to what is now the current U.S. standard: in part, the dressed size of a 1-inch (nominal) board was fixed at 3 ⁄ 4 inch; while the dressed size of 2 inch (nominal) lumber was reduced from 1 + 5 ⁄ 8 inch to the current 1 + 1 ⁄ 2 inch.

5. Parallel-strand lumber - Wikipedia

   en.wikipedia.org/wiki/Parallel-strand_lumber

   The beams are continuously formed, so the length of the beam is limited only to the maximum length that can be handled and transported. Typical widths are 3 + 1 ⁄ 2, 5 + 1 ⁄ 4 or 7 inches (89, 133 or 178 mm); typical depths are 9 + 1 ⁄ 2, 11 + 7 ⁄ 8, 14, 16 and 18 inches (240, 300, 360, 410 and 460 mm). Typically the beams are made to a ...

6. BS 1088 - Wikipedia

   en.wikipedia.org/wiki/BS_1088

   15 mm +.1/-0.9; 18 mm +.12/-0.98; 22 mm +.16/-1.08; 25 mm +1.8/-1.16 From the above we can assume that 6 mm material will arrive at thickness' between 6.04 mm and 5.35 mm. Face Veneer thickness -- For any three-ply construction, which applies to 3 and 4 mm material, each face veneer shall be not thinner than 1/8 of the total thickness of ...

7. Wood veneer - Wikipedia

   en.wikipedia.org/wiki/Wood_veneer

   Veneers are cut as thin as 0.64 mm (1 ⁄ 40 in). Depending on the cutting process used by the veneer manufacturer, very little wood is wasted by the saw blade thickness, known as the saw kerf. Some manufacturers use a very wide knife to slice off the thin veneer pieces. In this process, none of the wood is wasted.

8. AOL Mail

   mail.aol.com

   Get AOL Mail for FREE! Manage your email like never before with travel, photo & document views. Personalize your inbox with themes & tabs. You've Got Mail!

9. Framing (construction) - Wikipedia

   en.wikipedia.org/wiki/Framing_(construction)

   Studs usually consist of 1 + 1 ⁄ 2-by-3 + 1 ⁄ 2-inch (38 mm × 89 mm) or 1 + 1 ⁄ 2-by-5 + 1 ⁄ 2-inch (38 mm × 140 mm) lumber and are commonly spaced at 16 inches (410 mm) on center. This spacing may be changed to 12 or 24 inches (300 or 610 mm) on center depending on the load and the limitations imposed by the type and thickness of the ...