enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Nominal Pipe Size - Wikipedia

   en.wikipedia.org/wiki/Nominal_Pipe_Size

   Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

3. Pipe (fluid conveyance) - Wikipedia

   en.wikipedia.org/wiki/Pipe_(fluid_conveyance)

   For example, NPS 2 inch and DN 50 are the same pipe, but the actual OD is 2.375 inches or 60.33 millimetres. The only way to obtain the actual OD is to look it up in a reference table. For pipe sizes of NPS 14 inch (DN 350) and greater the NPS size is the actual diameter in inches and the DN size is equal to NPS times 25 (not 25.4) rounded to a ...

4. British Standard Pipe - Wikipedia

   en.wikipedia.org/wiki/British_Standard_Pipe

   These standard pipe threads are formally referred to by the following sequence of blocks: the words, Pipe thread, the document number of the standard (e.g., ISO 7 or EN 10226) the symbol for the pipe thread type: G, external and internal parallel (ISO 228) R, external taper (ISO 7) Rp, internal parallel (ISO 7/1) Rc, internal taper (ISO 7)

5. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

6. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25).

7. Cross-linked polyethylene - Wikipedia

   en.wikipedia.org/wiki/Cross-linked_polyethylene

   A cross-linked polyethylene (PEX) pipe. Cross-linked polyethylene, commonly abbreviated PEX, XPE or XLPE, is a form of polyethylene with cross-links.It is used predominantly in building services pipework systems, hydronic radiant heating and cooling systems, domestic water piping, insulation for high tension (high voltage) electrical cables, and baby play mats.

8. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   Pipe Threads, General Purpose (Inch) Pipe Thread Form ANSI B1.20.3-1976 (R2013) Dryseal Pipe Threads (Inch) Pipe Thread Form ASME B1.20.7-1991 (R2013) Hose Coupling Screw Threads - Inch: Pipe Thread Form ASME B1.21M-1997 (R2013) Metric Screw Threads - MJ Profile: V Thread Form BS 84: Tables of BS Whitworth, BS Fine and BS Pipe Threads: V Thread ...

9. Manhattan Project - Wikipedia

   en.wikipedia.org/wiki/Manhattan_Project

   Manhattan District The Trinity test of the Manhattan Project on 16 July 1945 was the first detonation of a nuclear weapon. Active 1942–1946 Disbanded 15 August 1947 Country United States United Kingdom Canada Branch U.S. Army Corps of Engineers Garrison/HQ Oak Ridge, Tennessee, U.S. Anniversaries 13 August 1942 Engagements Allied invasion of Italy Allied invasion of France Allied invasion of ...