enow.com Web Search

  1. Ads

    related to: allen bolt standard sizes

Search results

  1. Results from the WOW.Com Content Network
  2. Hex key - Wikipedia

    en.wikipedia.org/wiki/Hex_key

    Hex keys of various sizes with ball ends. Tamper-resistant hex screws have a protruding pin in the center of the hex recess that prevents insertion of standard hex keys; as such, they can only be fastened and removed with a special key that has a recess for the pin. A similar "center pin reject" security feature is also used on torx screws.

  3. ISO metric screw thread - Wikipedia

    en.wikipedia.org/wiki/ISO_metric_screw_thread

    Hexagonal (generally abbreviated to "hex") head widths (width across flats, spanner size) are for DIN 934 hex nuts and hex head bolts. Other (usually smaller) sizes may occur to reduce weight or cost, including the small series flange bolts defined in ISO 4162 which typically have hexagonal head sizes corresponding to the smaller 1st choice ...

  4. Preferred metric sizes - Wikipedia

    en.wikipedia.org/wiki/Preferred_metric_sizes

    Machine screws with different thread diameters Hex key set with metric sizes from 2 mm to 10 mm according to sizes for use with ISO 262 screw sizes (except 3.5 mm for M6 internal set screw) For each size bolt or screw and type of head, there is a corresponding size driver prescribed by various ISO standards, including: Internal hex drive: ISO ...

  5. List of screw drives - Wikipedia

    en.wikipedia.org/wiki/List_of_screw_drives

    In Japan, the male sizes are often designated as DTC-20, DTC-27, DTC-40 (discontinued) and DTC-45 corresponding to a respective screw head size of 3.2 mm, 4.6 mm, 6.4 mm and 7.7 mm; with the size of the screw measured across the widest portion of the mating part of the head. The most common sizes in use for consumer electronics are DTC-20 and ...

  6. List of screw and bolt types - Wikipedia

    en.wikipedia.org/wiki/List_of_screw_and_bolt_types

    An ASME B18.2.1 compliant cap screw has somewhat tighter tolerances than a hex bolt for the head height and the shank length. The nature of the tolerance difference allows an ASME B18.2.1 hex cap screw to always fit where a hex bolt is installed but a hex bolt could be slightly too large to be used where a hex cap screw is designed in. Fine ...

  7. Computer case screws - Wikipedia

    en.wikipedia.org/wiki/Computer_case_screws

    All three patterns may also be combined with a slot for a flat-blade screwdriver. Usually they are provided with a 1/4 in (0.25 inches (6.4 mm)) flanged hex head. Non-standard metricized 5.5 millimetres (0.22 in) flanged hex heads can also be encountered. Also common are pan head screws - a low disk with a chamfered outer edge.

  8. British Standard Whitworth - Wikipedia

    en.wikipedia.org/wiki/British_Standard_Whitworth

    British Standard Whitworth (BSW) is an imperial-unit-based screw thread standard, devised and specified by Joseph Whitworth in 1841 and later adopted as a British Standard. It was the world's first national screw thread standard, and is the basis for many other standards, such as BSF , BSP , BSCon , and BSCopper .

  9. List of thread standards - Wikipedia

    en.wikipedia.org/wiki/List_of_thread_standards

    Standard Name Type Example ASME B1.1-2003 (R2018) Unified Inch Screw Threads (UN and UNR Thread Form) V Thread Form: 1 ⁄ 4 ″-20 UNC #4-40 UNC ASME B1.5-1997 (R2014) Acme Screw Threads: Trapezoidal Thread Form: Tr 60×9 ANSI/ASME B1.9-1973 (R2017) Buttress Inch Screw Threads: Breech-Lock Thread Form: ASME B1.10M-2004 (R2014) Unified ...

  1. Ads

    related to: allen bolt standard sizes