enow.com Web Search

  1. Ad

    related to: equivalent duct diameter calculator

Search results

  1. Results from the WOW.Com Content Network
  2. Hydraulic diameter - Wikipedia

    en.wikipedia.org/wiki/Hydraulic_diameter

    For a fully filled duct or pipe whose cross-section is a convex regular polygon, the hydraulic diameter is equivalent to the diameter of a circle inscribed within the wetted perimeter. This can be seen as follows: The N {\displaystyle N} -sided regular polygon is a union of N {\displaystyle N} triangles, each of height D / 2 {\displaystyle D/2 ...

  3. Darcy friction factor formulae - Wikipedia

    en.wikipedia.org/wiki/Darcy_friction_factor_formulae

    The Reynolds number Re is taken to be Re = V D / ν, where V is the mean velocity of fluid flow, D is the pipe diameter, and where ν is the kinematic viscosity μ / ρ, with μ the fluid's Dynamic viscosity, and ρ the fluid's density. The pipe's relative roughness ε / D, where ε is the pipe's effective roughness height and D the pipe ...

  4. Darcy–Weisbach equation - Wikipedia

    en.wikipedia.org/wiki/Darcy–Weisbach_equation

    For laminar flow in a circular pipe of diameter , the friction factor is inversely proportional to the Reynolds number alone (f D = ⁠ 64 / Re ⁠) which itself can be expressed in terms of easily measured or published physical quantities (see section below). Making this substitution the Darcy–Weisbach equation is rewritten as

  5. Friction loss - Wikipedia

    en.wikipedia.org/wiki/Friction_loss

    Note that, in approximation, for a given value of flow volume, a step up in duct size (say from 100mm to 120mm) will reduce the friction loss by a factor of 3. Volumetric Flow Q of air at STP where friction loss per unit length Δ p / L (SI kg / m 2 / s 2 ) is, resp., 0.082, 0.245, and 0.816., for selected Nominal Duct Sizes [ 19 ] in smooth ...

  6. Reynolds number - Wikipedia

    en.wikipedia.org/wiki/Reynolds_number

    D i is the outside diameter of the inner pipe. For calculation involving flow in non-circular ducts, the hydraulic diameter can be substituted for the diameter of a circular duct, with reasonable accuracy, if the aspect ratio AR of the duct cross-section remains in the range ⁠ 1 / 4 ⁠ < AR < 4. [11]

  7. Process duct work - Wikipedia

    en.wikipedia.org/wiki/Process_Duct_Work

    The duct flange normally has 3/4" bolts at 6" nominal; spacing. Duct flange angle thickness needs to be designed for duct plate tensile stresses, as flanges will bend. 5/16" or 3/8" angle thicknesses are common. See above photo of round duct elbows, transitions, and stiffeners. The duct elbow radius is from 1 1/2 to 2 times the duct diameter.

  8. Nominal Pipe Size - Wikipedia

    en.wikipedia.org/wiki/Nominal_Pipe_Size

    Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

  9. Characteristic length - Wikipedia

    en.wikipedia.org/wiki/Characteristic_length

    For example, it is used to calculate flow through circular and non-circular tubes in order to examine flow conditions (i.e., the Reynolds number). In those cases, the characteristic length is the diameter of the pipe or, in case of non-circular tubes, its hydraulic diameter D h {\displaystyle D_{h}} :

  1. Ad

    related to: equivalent duct diameter calculator