enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Nominal Pipe Size - Wikipedia

   en.wikipedia.org/wiki/Nominal_Pipe_Size

   Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

3. Hydraulic diameter - Wikipedia

   en.wikipedia.org/wiki/Hydraulic_diameter

   For a fully filled duct or pipe whose cross-section is a convex regular polygon, the hydraulic diameter is equivalent to the diameter of a circle inscribed within the wetted perimeter. This can be seen as follows: The N {\displaystyle N} -sided regular polygon is a union of N {\displaystyle N} triangles, each of height D / 2 {\displaystyle D/2 ...

4. Orders of magnitude (length) - Wikipedia

   en.wikipedia.org/wiki/Orders_of_magnitude_(length)

   1 cm – 0.39 inches; 1 cm – edge of a square of area 1 cm 2; 1 cm – edge of a cube of volume 1 mL; 1 cm – length of a coffee bean; 1 cm – approximate width of average fingernail; 1.2 cm – length of a bee; 1.2 cm – diameter of a die; 1.5 cm – length of a very large mosquito; 1.6 cm – length of a Jaragua Sphaero, a very small reptile

5. Preferred metric sizes - Wikipedia

   en.wikipedia.org/wiki/Preferred_metric_sizes

   Machine screws with different thread diameters Hex key set with metric sizes from 2 mm to 10 mm according to sizes for use with ISO 262 screw sizes (except 3.5 mm for M6 internal set screw) For each size bolt or screw and type of head, there is a corresponding size driver prescribed by various ISO standards, including:

6. Pipe (fluid conveyance) - Wikipedia

   en.wikipedia.org/wiki/Pipe_(fluid_conveyance)

   For pipe sizes of NPS 14 inch (DN 350) and greater the NPS size is the actual diameter in inches and the DN size is equal to NPS times 25 (not 25.4) rounded to a convenient multiple of 50. For example, NPS 14 has an OD of 14 inches or 355.60 millimetres, and is equivalent to DN 350.

7. Area - Wikipedia

   en.wikipedia.org/wiki/Area

   Although there are 10 mm in 1 cm, there are 100 mm 2 in 1 cm 2. Calculation of the area of a square whose length and width are 1 metre would be: 1 metre × 1 metre = 1 m 2. and so, a rectangle with different sides (say length of 3 metres and width of 2 metres) would have an area in square units that can be calculated as: 3 metres × 2 metres ...

8. Piping and plumbing fitting - Wikipedia

   en.wikipedia.org/wiki/Piping_and_plumbing_fitting

   A reducer reduces the pipe size from a larger to a smaller bore (inner diameter). Alternatively, reducer may refer to any fitting which causes a change in pipe diameter. [15] This change may be intended to meet hydraulic flow requirements of the system or adapt to existing piping of a different size. The reduction length is usually equal to the ...

9. Iron pipe size - Wikipedia

   en.wikipedia.org/wiki/Iron_pipe_size

   Iron Pipe Size (IPS or I.P.S.) pipe sizing system based on the inside diameter (ID) of pipe. It was widely used from the early 19th century to the mid 20th century and is still in use by some industries, including major PVC pipe manufacturers, as well as for some legacy drawings and equipment.