enow.com Web Search

  1. Ads

    related to: 7 inch flexible duct hose sizes guide

Search results

  1. Results from the WOW.Com Content Network
  2. AN thread - Wikipedia

    en.wikipedia.org/wiki/AN_thread

    A 37° flare type end fitting for flexible hose The AN thread (also A-N ) is a particular type of fitting used to connect flexible hoses and rigid metal tubing that carry fluid. It is a US military-derived specification that dates back to World War II and stems from a joint standard agreed upon by the Army Air Corps and Navy, hence AN.

  3. Hard suction hose - Wikipedia

    en.wikipedia.org/wiki/Hard_suction_hose

    5-inch (13 cm) flex suction hose with Storz fittings, mounted on an engine. Flexible suction hose (Flex suction or suction hose), not to be confused with hard suction hose in U.S., is a specific type of fire hose used in drafting operations, when a fire engine uses a vacuum to draw water from a portable water tank, pool, or other static water source.

  4. Piping and plumbing fitting - Wikipedia

    en.wikipedia.org/wiki/Piping_and_plumbing_fitting

    Piping or tubing is usually inserted into fittings to make connections. Connectors are assigned a gender, abbreviated M or F. An example of this is a "3 ⁄ 4-inch female adapter NPT", which would have a corresponding male connection of the same size and thread standard (in this case also NPT).

  5. Storz - Wikipedia

    en.wikipedia.org/wiki/Storz

    The 100 mm (4-inch) and 125 mm (5-inch) Storz couplers have been specified in NFPA 1963, Standard for Fire Hose Connections, since the 1993 edition. U.S. cities that have fire hydrants with 125 mm Storz connectors include Raleigh, NC [ 5 ] and the City of Corvallis, OR (adapter on 4-inch threaded outlet).

  6. Garden hose - Wikipedia

    en.wikipedia.org/wiki/Garden_hose

    The US standard was defined by NFPA 1963, "Standard for Fire Hose Connections", [2] then later by ANSI-ASME B1.20.7, [3] which specifies 1 + 1 ⁄ 16 inches (27 mm) diameter straight (non-tapered) thread with a pitch of 11.5 threads per inch (TPI). The female thread is abbreviated FHT (for "female hose thread"), and the male part is abbreviated ...

  7. North American Fire Hose Coupler Incompatibilities - Wikipedia

    en.wikipedia.org/wiki/North_American_Fire_Hose...

    At its annual convention at Dallas, TX, the NFPA formally adopted a standard with 2 + 1 ⁄ 2-inch hose with 7.5 threads per inch as the primary standard, with additional sizes of 3 and 3.5 inches (each with 6 threads per inch) and a 4.5 inch coupling with 4 threads per inch, with the fire hydrant standard specifying one 4.5 inch port and two 2 ...

  8. Duct (flow) - Wikipedia

    en.wikipedia.org/wiki/Duct_(flow)

    Kinks in flexible ducting must be avoided. Some flexible duct markets prefer to avoid using flexible duct on the return air portions of HVAC systems, however flexible duct can tolerate moderate negative pressures. The UL181 test requires a negative pressure of 200 Pa. To use flexible ducting in a system, make sure to pull the duct tight so you ...

  9. Pipe (fluid conveyance) - Wikipedia

    en.wikipedia.org/wiki/Pipe_(fluid_conveyance)

    Pipe sizes can be confusing because the terminology may relate to historical dimensions. For example, a half-inch iron pipe does not have any dimension that is a half inch. Initially, a half inch pipe did have an inner diameter of 1 ⁄ 2 inch (13 mm)—but it also had thick walls. As technology improved, thinner walls became possible, but the ...

  1. Ads

    related to: 7 inch flexible duct hose sizes guide