enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Threaded insert - Wikipedia

   en.wikipedia.org/wiki/Threaded_insert

   TIME-SERT insert. A threaded insert, also known as a threaded bushing, is a fastener element that is inserted into an object to add a threaded hole. [1] They may be used to repair a stripped threaded hole, provide a durable threaded hole in a soft material, place a thread on a material too thin to accept it, mold or cast threads into a work piece thereby eliminating a machining operation, or ...

3. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   The major diameter may be slightly different from the shank diameter, which is the diameter of the unthreaded part of the screw. The diameters are sometimes given approximately in fractions of an inch (e.g. the major diameter of a #6 screw is 0.1380 in, approximately 9 ⁄ 64 in = 0.140625 in). The pitch P is the distance between thread peaks.

4. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   In 1913, Woolley and Meredith defined them like Anthony, but gave the following dimensions: hex head cap screws up to and including 7 ⁄ 16 inch (11.1125 mm) have a head that is 3 ⁄ 16 inch (4.7625 mm) larger than the shank diameter; screws greater than 1 ⁄ 2 inch (12.7 mm) in diameter have a head that is 1 ⁄ 4 inch (6.35 mm) larger than ...

5. Screw - Wikipedia

   en.wikipedia.org/wiki/Screw

   A machine screw or bolt is usually a smaller fastener (less than 1 ⁄ 4 inch (6.35 mm) in diameter) threaded the entire length of its shank that usually has a recessed drive type (slotted, Phillips, etc.), usually intended to screw into a pre-formed thread, either a nut or a threaded (tapped) hole, unlike a wood or self-tapping screw. Machine ...

6. Tap and die - Wikipedia

   en.wikipedia.org/wiki/Tap_and_die

   where is the tap drill size, is the major diameter of the tap (e.g., 3 ⁄ 8 in for a 3 ⁄ 8-16 tap), and / is the thread pitch (1 ⁄ 16 inch in the case of a 3 ⁄ 8-16 tap). For a 3 ⁄ 8-16 tap, the above formula would produce 5 ⁄ 16, which is the correct tap drill diameter. The above formula ultimately results in an approximate 75% thread.

7. Square thread form - Wikipedia

   en.wikipedia.org/wiki/Square_thread_form

   where Sq designates a square thread, 60 is the nominal diameter in millimeters, and 9 is the pitch in millimeters. When there is no suffix it is a single start thread. If there is a suffix then the value after the multiplication sign is the lead and the value in the parentheses is the pitch. For example:

8. Nut (hardware) - Wikipedia

   en.wikipedia.org/wiki/Nut_(hardware)

   A (usually square) nut in a spring steel cage which wraps around the nut. The cage has two wings that when compressed allow the cage to be inserted into the square holes Clip-on nut: J-nut or U-nut, sheet metal nut, speed nut (ambiguously) Designed to be clipped to sheet metal Coupling nut: Extension nut

9. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25). If the pitch is the normally used "coarse" pitch listed in ISO 261 or ...