enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

3. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   In 1913, Woolley and Meredith defined them like Anthony, but gave the following dimensions: hex head cap screws up to and including 7 ⁄ 16 inch (11.1125 mm) have a head that is 3 ⁄ 16 inch (4.7625 mm) larger than the shank diameter; screws greater than 1 ⁄ 2 inch (12.7 mm) in diameter have a head that is 1 ⁄ 4 inch (6.35 mm) larger than ...

4. Drill bit sizes - Wikipedia

   en.wikipedia.org/wiki/Drill_bit_sizes

   So a 1 / 2 in (12.7 mm) diameter drill will be able to drill a hole 4 + 1 / 2 in (114.3 mm) deep, since it is 9 times the diameter in length. A 1 / 8 in (3.175 mm) diameter drill can drill a hole 1 + 5 / 8 in (41.275 mm) deep, since it is 13 times the diameter in flute length. [3]

5. Wrench size - Wikipedia

   en.wikipedia.org/wiki/Wrench_size

   Sizes that may interchange, depending on the precision needed, include 2 mm (close to 5 ⁄ 64 inch (1.98 mm)), 4 mm (close to 5 ⁄ 32 inch (3.97 mm)) and 8 mm (close to 5 ⁄ 16 inch (7.94 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

6. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25). If the pitch is the normally used "coarse" pitch listed in ISO 261 or ...

7. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   The major diameter may be slightly different from the shank diameter, which is the diameter of the unthreaded part of the screw. The diameters are sometimes given approximately in fractions of an inch (e.g. the major diameter of a #6 screw is 0.1380 in, approximately 9 ⁄ 64 in = 0.140625 in). The pitch P is the distance between thread peaks.

8. AOL

   search.aol.com

   The search engine that helps you find exactly what you're looking for. Find the most relevant information, video, images, and answers from all across the Web.

9. Screw thread - Wikipedia

   en.wikipedia.org/wiki/Screw_thread

   Calipers measure the female minor diameter (inside diameter, ID), which is less than caliper measurement of the male major diameter (outside diameter, OD). For example, tables of caliper measurements show 0.69 female ID and 0.75 male OD for the standards of "3/4 SAE J512" threads and "3/4-14 UNF JIS SAE-J514 ISO 8434-2". [ 6 ]