enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. North American Fire Hose Coupler Incompatibilities - Wikipedia

   en.wikipedia.org/wiki/North_American_Fire_Hose...

   At its annual convention at Dallas, TX, the NFPA formally adopted a standard with 2 + 1 ⁄ 2-inch hose with 7.5 threads per inch as the primary standard, with additional sizes of 3 and 3.5 inches (each with 6 threads per inch) and a 4.5 inch coupling with 4 threads per inch, with the fire hydrant standard specifying one 4.5 inch port and two 2 ...

3. Nominal Pipe Size - Wikipedia

   en.wikipedia.org/wiki/Nominal_Pipe_Size

   Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

4. Hose coupling - Wikipedia

   en.wikipedia.org/wiki/Hose_coupling

   Also called John Morris Coupling, BS336 Instantaneous fire couplings are similar in design to the camlock fittings, and are used by; UK, Irish, New Zealand, Indian & Hong Kong fire brigades. They are available in two sizes: 1 + 1 ⁄ 2-inch INST (FETA, only available with 38 mm hose tails) and 2 + 1 ⁄ 2-inch INST (BS336).

5. Microphone connector - Wikipedia

   en.wikipedia.org/wiki/Microphone_connector

   Photo: 2.5 mm mono (TS), 3.5 mm mono and stereo (TRS), and 1 ⁄ 4 inch (6.4 mm) stereo (TRS) phone connectors The most common microphone connector in consumer use is the venerable phone connector, in 1 ⁄ 4 inch (6.4 mm), 3.5 mm, and 2.5 mm sizes, and in both mono and stereo configurations.

6. Concentric reducer - Wikipedia

   en.wikipedia.org/wiki/Concentric_reducer

   A copper concentric reducer. A concentric reducer is used to join pipe sections or tube sections on the same axis. [1] The concentric reducer is cone-shaped, and is used when there is a shift in diameter between pipes. [1] For example, when a 1" pipe transitions into a 3/4" pipe and the top or bottom of the pipe doesn't need to remain level. [2]

7. Hard suction hose - Wikipedia

   en.wikipedia.org/wiki/Hard_suction_hose

   5-inch (13 cm) flex suction hose with Storz fittings, mounted on an engine. Flexible suction hose (Flex suction or suction hose), not to be confused with hard suction hose in U.S., is a specific type of fire hose used in drafting operations, when a fire engine uses a vacuum to draw water from a portable water tank, pool, or other static water source.

8. List of disk drive form factors - Wikipedia

   en.wikipedia.org/wiki/List_of_disk_drive_form...

   8-, 5.25-, 3.5-, 2.5-, 1.8- and 1-inch HDDs, together with a ruler to show the length of platters and read-write heads A newer 2.5-inch (63.5 mm) 6,495 MB HDD compared to an older 5.25-inch full-height 110 MB HDD. IBM's first hard drive, the IBM 350, used a stack of fifty 24-inch platters and was of a size comparable to two large refrigerators.

9. National pipe thread - Wikipedia

   en.wikipedia.org/wiki/National_pipe_thread

   The taper rate for all NPT threads is 1 inch of diameter in 16 inches of length (3 ⁄ 4 inch per foot or 62.5 millimeters per meter) measured by the change of diameter (of the pipe thread) over distance of thread.