enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Schematic of a machine tap. Below is a comprehensive drill and tap size chart for all drills and taps, imperial and metric, up to 36.5 millimetres (1.44 in) in diameter.. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

  3. Drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    From 1.0 through 2.95 mm, sizes are defined as follows, where N is an integer from 10 through 29: N · 0.1 mm; N · 0.1 + 0.05 mm; From 3.0 through 13.9 mm, sizes are defined as follows, where N is an integer from 30 through 139: N · 0.1 mm; From 14.0 through 25.0 mm, sizes are defined as follows, where M is an integer from 14 through 25: M ...

  4. 9 mm caliber - Wikipedia

    en.wikipedia.org/wiki/9_mm_caliber

    This is a list of firearm cartridges that have bullets in the 9 millimeters (0.35 in) to 9.99 millimeters (0.393 in) caliber range. Case length refers to the round case length. OAL refers to the overall length of the loaded round. All measurements are given in millimeters, followed by the equivalent in inches between parentheses.

  5. Wrench size - Wikipedia

    en.wikipedia.org/wiki/Wrench_size

    Sizes that may interchange, depending on the precision needed, include 2 mm (close to 5 ⁄ 64 inch (1.98 mm)), 4 mm (close to 5 ⁄ 32 inch (3.97 mm)) and 8 mm (close to 5 ⁄ 16 inch (7.94 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

  6. Gauge (firearms) - Wikipedia

    en.wikipedia.org/wiki/Gauge_(firearms)

    An n-gauge diameter means that a ball of lead (density 11.34 g/cm 3 or 0.4097 lb/in 3) with that diameter has a mass equal to ⁠ 1 / n ⁠ part of the mass of the international avoirdupois pound (approx. 454 grams), that is, that n such lead balls could be cast from a pound weight of lead.

  7. Inch - Wikipedia

    en.wikipedia.org/wiki/Inch

    Subdivisions of an inch are typically written using dyadic fractions with odd number numerators; for example, two and three-eighths of an inch would be written as ⁠2 + 3 / 8 ⁠ ″ and not as 2.375″ nor as ⁠2 + 6 / 16 ⁠ ″. However, for engineering purposes fractions are commonly given to three or four places of decimals and have been ...

  8. Thousandth of an inch - Wikipedia

    en.wikipedia.org/wiki/Thousandth_of_an_inch

    Other common terms used in machining with Imperial units involve adding tenths together to achieve a specific tolerance or measurement. For example, "five tenths," is typically a measurement or tolerance of five ten-thousandths of an inch, and written as 0.0005 inches. "Three tenths," as another example, is written as 0.0003 inches [9]

  9. Ring size - Wikipedia

    en.wikipedia.org/wiki/Ring_size

    In Russia, ring sizes are equal to the inner diameter rounded to whole and half numbers, sometimes to quarters, for example diameter 16.92 mm is equal to size 17, 16.1 mm is equal to size 16. Equivalency table