enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Nominal Pipe Size - Wikipedia

   en.wikipedia.org/wiki/Nominal_Pipe_Size

   Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

3. Casing string - Wikipedia

   en.wikipedia.org/wiki/Casing_string

   A typical piece of casing might be described as 9-5/8" 53.5# P-110 LT&C Rg 3: specifying OD, weight per foot (53.5 lbm/ft thus 0.545-inch wall thickness and 8.535-inch inside diameter), steel strength (110,000 psi yield strength), end finish ("Long Threaded and Coupled"), and approximate length ("Range 3" usually runs between 40 and 42 feet).

4. Pipe (fluid conveyance) - Wikipedia

   en.wikipedia.org/wiki/Pipe_(fluid_conveyance)

   The history of copper pipe is similar. In the 1930s, the pipe was designated by its internal diameter and a 1 ⁄ 16-inch (1.6 mm) wall thickness. Consequently, a 1-inch (25 mm) copper pipe had a 1 + 1 ⁄ 8-inch (28.58 mm) outside diameter. The outside diameter was the important dimension for mating with fittings.

5. Process duct work - Wikipedia

   en.wikipedia.org/wiki/Process_Duct_Work

   When tubes are used for these purposes they may be 10'-6" to 12 foot diameter, and up to 250 foot long, using up to 1/2" plate and ovaling ring stiffeners at 8 foot (to 20 foot centers). On one such project My firm added L8x8x3/4 at the top 45 degree location to stiffen the plate near the point of maximum stress for tubes (as per Timoshenko ...

6. Piping and plumbing fitting - Wikipedia

   en.wikipedia.org/wiki/Piping_and_plumbing_fitting

   Steel pipe is often joined with threaded connections; tapered threads are cut into the end of the pipe, and sealant is applied in the form of thread-sealing compound or thread seal tape (also known as PTFE or Teflon tape) and the pipe is screwed into a threaded fitting with a pipe wrench. Threaded steel pipe is widely used in buildings to ...

7. Electrical conduit - Wikipedia

   en.wikipedia.org/wiki/Electrical_conduit

   Galvanized rigid conduit (GRC) is galvanized steel tubing, with a tubing wall that is thick enough to allow it to be threaded. Its common applications are in commercial and industrial construction. [1] It is designed to protect wire and connectors. Intermediate metal conduit (IMC) is a steel tubing heavier than EMT but lighter than RMC. It may ...

8. AOL Mail

   mail.aol.com/d?reason=invalid_cred

   Get AOL Mail for FREE! Manage your email like never before with travel, photo & document views. Personalize your inbox with themes & tabs. You've Got Mail!

9. Fire sprinkler system - Wikipedia

   en.wikipedia.org/wiki/Fire_sprinkler_system

   For example, in an office building classified as light hazard, a typical design area would be 1,500 square feet (140 m 2) and the design density would be 0.1 US gallons per minute (0.38 L/min) per 1 square foot (0.093 m 2) or a minimum of 150 US gallons per minute (570 L/min) applied over the 1,500-square-foot (140 m 2) design area.