enow.com Web Search

  1. Ads

    related to: 1 4 28 zerk fitting size

Search results

  1. Results from the WOW.Com Content Network
  2. Grease fitting - Wikipedia

    en.wikipedia.org/wiki/Grease_fitting

    Grease fitting on a bearing A grease nipple on the driver's door of a 1956 VW Beetle. A grease fitting, grease nipple, Zerk fitting, grease zerk, Alemite fitting, or divit is a metal fitting used in mechanical systems to feed lubricants, usually lubricating grease, into a bearing under moderate to high pressure using a grease gun.

  3. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Below is a comprehensive drill and tap size chart for all drills and taps: Inch, imperial, and metric, up to 36.5 millimetres (1.44 in) in diameter. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

  4. List of thread standards - Wikipedia

    en.wikipedia.org/wiki/List_of_thread_standards

    ASME B1.20.1-2013: Pipe Threads, General Purpose (Inch) Pipe Thread Form ANSI B1.20.3-1976 (R2013) Dryseal Pipe Threads (Inch) Pipe Thread Form ASME B1.20.7-1991 (R2013) Hose Coupling Screw Threads - Inch: Pipe Thread Form ASME B1.21M-1997 (R2013) Metric Screw Threads - MJ Profile: V Thread Form BS 84: Tables of BS Whitworth, BS Fine and BS ...

  5. Unified Thread Standard - Wikipedia

    en.wikipedia.org/wiki/Unified_Thread_Standard

    The standard designation for a UTS thread is a number indicating the nominal (major) diameter of the thread, followed by the pitch measured in threads per inch.For diameters smaller than ⁠ 1 / 4 ⁠ inch, the diameter is indicated by an integer number defined in the standard; for all other diameters, the inch figure is given.

  6. AN thread - Wikipedia

    en.wikipedia.org/wiki/AN_thread

    Each AN size also uses its own standard thread size. AN fittings are a flare fitting , using 37° flared tubing to form a metal-to-metal seal. They are similar to other 37° flared fittings, such as JIC , which is their industrial variant. [ 2 ]

  7. British Standard Pipe - Wikipedia

    en.wikipedia.org/wiki/British_Standard_Pipe

    In the modern standard metric version, it is simply a size number, where listed diameter size is the major outer diameter of the external thread. For a taper thread, it is the diameter at the "gauge length" (plus/minus one thread pitch) from the small end of the thread.

  8. National pipe thread - Wikipedia

    en.wikipedia.org/wiki/National_pipe_thread

    The half-angle (between the taper surface and the axis of the pipe) is arctan(1 ⁄ 32) ≈ 1.7899° ≈ 1° 47′. The standard for Nominal Pipe Size (often abbreviated NPS, which should not be confused with the abbreviation NPS for the straight thread form standard) is loosely related to the inside diameter of Schedule 40 series of sizes.

  9. ISO metric screw thread - Wikipedia

    en.wikipedia.org/wiki/ISO_metric_screw_thread

    A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25). If the pitch is the normally used "coarse" pitch listed in ISO 261 or ...

  1. Ads

    related to: 1 4 28 zerk fitting size