enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Nominal Pipe Size - Wikipedia

   en.wikipedia.org/wiki/Nominal_Pipe_Size

   Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

3. Organ flue pipe scaling - Wikipedia

   en.wikipedia.org/wiki/Organ_flue_pipe_scaling

   Relationship between number of feet, octave and size of an open flue pipe (1′ = 1 foot = about 32 cm) Play ⓘ Scaling is the ratio of an organ pipe's diameter to its length. The scaling of a pipe is a major influence on its timbre. Reed pipes are scaled according to different formulas than for flue pipes.

4. National pipe thread - Wikipedia

   en.wikipedia.org/wiki/National_pipe_thread

   The taper rate for all NPT threads is 1 inch of diameter in 16 inches of length (3 ⁄ 4 inch per foot or 62.5 millimeters per meter) measured by the change of diameter (of the pipe thread) over distance of thread. The half-angle (between the taper surface and the axis of the pipe) is arctan(1 ⁄ 32) ≈ 1.7899° ≈ 1° 47′.

5. Rod (unit) - Wikipedia

   en.wikipedia.org/wiki/Rod_(unit)

   The rod, perch, or pole (sometimes also lug) is a surveyor's tool [1] and unit of length of various historical definitions. In British imperial and US customary units, it is defined as 16 + 1 ⁄ 2 feet, equal to exactly 1 ⁄ 320 of a mile, or 5 + 1 ⁄ 2 yards (a quarter of a surveyor's chain), and is exactly 5.0292 meters.

6. Hydraulic diameter - Wikipedia

   en.wikipedia.org/wiki/Hydraulic_diameter

   For a fully filled duct or pipe whose cross-section is a convex regular polygon, the hydraulic diameter is equivalent to the diameter of a circle inscribed within the wetted perimeter. This can be seen as follows: The N {\displaystyle N} -sided regular polygon is a union of N {\displaystyle N} triangles, each of height D / 2 {\displaystyle D/2 ...

7. Pipe (fluid conveyance) - Wikipedia

   en.wikipedia.org/wiki/Pipe_(fluid_conveyance)

   The history of copper pipe is similar. In the 1930s, the pipe was designated by its internal diameter and a 1 ⁄ 16-inch (1.6 mm) wall thickness. Consequently, a 1-inch (25 mm) copper pipe had a 1 + 1 ⁄ 8-inch (28.58 mm) outside diameter. The outside diameter was the important dimension for mating with fittings.

8. Iron pipe size - Wikipedia

   en.wikipedia.org/wiki/Iron_pipe_size

   During the IPS period, pipes were cast in halves and welded together, and pipe sizes referred to the inside diameters. [1] The inside diameters under IPS were roughly the same as the more modern Ductile Iron Pipe Standard (DIPS) and Nominal Pipe Size (NPS) Standards, and some of the wall thicknesses were also retained with a different ...

9. Organ pipe - Wikipedia

   en.wikipedia.org/wiki/Organ_pipe

   A pipe half the length of another will sound one octave higher. If the longest pipe, C, is 8 feet (2.4 m) in length, the pipe one octave higher will be 4 feet (1.2 m) long, and two octaves above (middle C) will be 2 feet (0.61 m) long. A closed (stopped) pipe produces a sound one octave lower than an open pipe.