enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

3. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   The advantage of this screw type over a self-drilling screw is that, if the screw is reinstalled, new threads are not cut as the screw is driven. set bolt: tap bolt, setscrew: A bolt that is threaded all the way to the head. An ASME B18.2.1 compliant set/tap bolt has the same tolerances as an ASME B18.2.1 compliant hex cap screw. set screw ...

4. Thread pitch gauge - Wikipedia

   en.wikipedia.org/wiki/Thread_pitch_gauge

   A thread gauge, [1] also known as a screw gauge [2] or pitch gauge, [3] is used to measure the pitch or lead of a screw thread. Thread pitch gauges are used as a reference tool in determining the pitch of a thread that is on a screw or in a tapped hole. This tool is not used as a precision measuring instrument, rather it allows the user to ...

5. Screw - Wikipedia

   en.wikipedia.org/wiki/Screw

   A machine screw or bolt is usually a smaller fastener (less than 1 ⁄ 4 inch (6.35 mm) in diameter) threaded the entire length of its shank that usually has a recessed drive type (slotted, Phillips, etc.), usually intended to screw into a pre-formed thread, either a nut or a threaded (tapped) hole, unlike a wood or self-tapping screw. Machine ...

6. Tap and die - Wikipedia

   en.wikipedia.org/wiki/Tap_and_die

   A forming tap, aka a fluteless tap or roll tap, forcefully displaces the metal into a thread shape upon being turned into the hole, instead of cutting metal from the sides of the hole as cutting taps do. A forming tap has lobes periodically spaced around the tap which actually do the thread forming as the tap is advanced into a properly sized ...

7. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   Even though #14 and #16 screws are still available, they are not as common as sizes #0 through #12. [citation needed] Sometimes "special" diameter and pitch combinations (UNS) are used, for example a 0.619 in (15.7 mm) major diameter with 20 threads per inch. UNS threads are rarely used for bolts, but rather on nuts, tapped holes, and threaded ODs.

8. Screw thread - Wikipedia

   en.wikipedia.org/wiki/Screw_thread

   Another common inspection point is the straightness of a bolt or screw. This topic comes up often when there are assembly issues with predrilled holes as the first troubleshooting point is to determine if the fastener or the hole is at fault. ASME B18.2.9 "Straightness Gage and Gaging for Bolts and Screws" was developed to address this issue.

9. Self-tapping screw - Wikipedia

   en.wikipedia.org/wiki/Self-tapping_screw

   A self-tapping screw is a screw that can tap its own hole as it is driven into the material. More narrowly, self-tapping is used only to describe a specific type of thread-cutting screw intended to produce a thread in relatively soft material or sheet materials, excluding wood screws .