enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Drill bit shank - Wikipedia

   en.wikipedia.org/wiki/Drill_bit_shank

   For example, this allows a 1 ⁄ 2-inch (13 mm) bit to be used in a pistol-grip drill's 3 ⁄ 8-inch (9.5 mm) chuck. One particular type of reduced-shank drill bits are Silver & Deming ( S&D ) bits, whose sets run from 9 ⁄ 16 -inch (14 mm) to 1 + 1 ⁄ 2 -inch (38 mm) drill body diameter with a standard 1 ⁄ 2 -inch (13 mm) reduced shank for ...

3. Chuck (engineering) - Wikipedia

   en.wikipedia.org/wiki/Chuck_(engineering)

   The term universal chuck also refers to this type. These chucks are best suited to grip circular or hexagonal cross-sections when very fast, reasonably accurate (±0.005 inch [0.125 mm] TIR) centering is desired. [citation needed] Sometimes this type of chuck has four or six jaws instead of three.

4. Socket wrench - Wikipedia

   en.wikipedia.org/wiki/Socket_wrench

   For example, a 1 ⁄ 4-inch to 3 ⁄ 8-inch adapter allows sockets with 1 ⁄ 4-inch drive holes to attach to a 3 ⁄ 8-inch ratchet, and so on. Universal joints are two articulated socket joints (about 1 inch (25 mm) long) combined at a right angle, that allow a bend in the turning axis of the wrench and socket. They are used with extensions ...

5. Machine taper - Wikipedia

   en.wikipedia.org/wiki/Machine_taper

   The rate of taper is 1:20 on diameter, in other words 0.600" on diameter per foot, .050" on diameter per inch. Tapers range from a Number 2 to a Number 20. The diameter of the big end in inches is always the taper size divided by 8, the small end is always the taper size divided by 10 and the length is the taper size divided by 2.

6. AOL Mail

   mail.aol.com

   Get AOL Mail for FREE! Manage your email like never before with travel, photo & document views. Personalize your inbox with themes & tabs. You've Got Mail!

7. Drill bit sizes - Wikipedia

   en.wikipedia.org/wiki/Drill_bit_sizes

   ANSI B94.11M-1979 sets size standards for jobber-length straight-shank twist drill bits from 1/64 inch through 1 inch in 1/64 inch increments. For Morse taper -shank drill bits, the standard continues in 1/64 inch increments up to 1¾ inch, then 1/32 inch increments up to 2¼ inch, 1/16 inch increments up to 3 inches, 1/8 inch increments up to ...

8. Tap and die - Wikipedia

   en.wikipedia.org/wiki/Tap_and_die

   where is the tap drill size, is the major diameter of the tap (e.g., 3 ⁄ 8 in for a 3 ⁄ 8-16 tap), and / is the thread pitch (1 ⁄ 16 inch in the case of a 3 ⁄ 8-16 tap). For a 3 ⁄ 8 -16 tap, the above formula would produce 5 ⁄ 16 , which is the correct tap drill diameter.

9. Drill - Wikipedia

   en.wikipedia.org/wiki/Drill

   Because the combined mass of the chuck and bit is comparable to that of the body of the drill, the energy transfer is inefficient and can sometimes make it difficult for larger bits to penetrate harder materials such as poured concrete. A standard hammer drill accepts 6 mm (1/4 inch) and 13 mm (1/2 inch) drill bits.