enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. EIA RF Connectors - Wikipedia

   en.wikipedia.org/wiki/EIA_RF_Connectors

   They are commonly referred to by the inner diameter of the outer conductor in fractional inches. Sizes covered under these two standards range from 3/8 to 6 1/8 inch outside diameter (OD) for 50 Ω and 3/8 to 3 1/8 inch OD for 75 Ω.

3. Drill bit sizes - Wikipedia

   en.wikipedia.org/wiki/Drill_bit_sizes

   Drill bit sizes are written as irreducible fractions. So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a chart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths).

4. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

5. Gauge (firearms) - Wikipedia

   en.wikipedia.org/wiki/Gauge_(firearms)

   However, the 3 + 1 ⁄ 2-inch (89 mm) 12-gauge shell, with its higher SAAMI pressure rating of 14,000 psi (97 MPa) compared to standard 2 + 3 ⁄ 4-inch (70 mm) and 3-inch (76 mm) 12-gauge shells with their lower pressure rating of 11,500 psi (79 MPa), began to approach the performance of the 3 + 1 ⁄ 2-inch (89 mm) 10-gauge shells with a ...

6. French catheter scale - Wikipedia

   en.wikipedia.org/wiki/French_catheter_scale

   The Charrière is measured by the ''outer'' diameter, and is defined as 1 Fr = 1/3 mm, and thus 1 mm = 3 Fr; therefore the diameter of a round catheter in millimetres can be determined by dividing the French size by 3. [2] The French units roughly correspond to the outer circumference of the catheter (see table below).

7. Template:Track gauge - Wikipedia

   en.wikipedia.org/wiki/Template:Track_gauge

   The template formats a track gauge size into standard notation and adds the conversion into the imperial/metric (other) size Template parameters [Edit template data] Parameter Description Type Status Track gauge definition 1 Defined track gauge, in mm or ft in. Also can accept: ' '', m, gauge name String required Link top measurement units lk =on: adds link to the gauge defining article String ...

8. Inch - Wikipedia

   en.wikipedia.org/wiki/Inch

   Metric (SI) units. 25.4 mm. A fire hydrant marked as 3-inch. The inch (symbol: in or ″) is a unit of length in the British Imperial and the United States customary systems of measurement. It is equal to ⁠ 1 36 ⁠ yard or ⁠ 1 12 ⁠ of a foot. Derived from the Roman uncia ("twelfth"), the word inch is also sometimes used to translate ...

9. Standard wire gauge - Wikipedia

   en.wikipedia.org/wiki/Standard_wire_gauge

   A table of the gauge numbers and wire diameters is shown below. [1] [2] The basis of the system is the thou (or mil in US English), or 0.001 in. Sizes are specified as wire diameters, stated in thou and tenths of a thou (mils and tenths). The wire diameter diminishes with increasing size number.