enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. Help:Convert units - Wikipedia

    en.wikipedia.org/wiki/Help:Convert_units

    When using "hand in" to convert to hands and inches, the rounded hands and inches values are equivalent, and use the same fraction, if any. Special rounding of the inches value only occurs when "hand in" is the output. For example, if the output is "in hand", the inches value is rounded independently from the hands value.

  3. Image sensor format - Wikipedia

    en.wikipedia.org/wiki/Image_sensor_format

    Sizes are often expressed as a fraction of an inch, with a one in the numerator, and a decimal number in the denominator. For example, 1/2.5 converts to 2/5 as a simple fraction, or 0.4 as a decimal number. This "inch" system gives a result approximately 1.5 times the length of the diagonal of the sensor.

  4. List of scale model sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_scale_model_sizes

    Derived from the used of 10 yards to 1 inch. Works well with 5mm miniatures where a 6' man equals 5.08 mm 1:350: 0.871 mm: Ship models: Though assumed to be a Japanese size for ship models, its origin lies in the UK, with the release of the 1:350 Javelin and Tribal Destroyer kit in December 1945 in the FROG Penguin range.

  5. f-number - Wikipedia

    en.wikipedia.org/wiki/F-number

    In the following quote, an "apertal ratio" of "1 ⁄ 24" is calculated as the ratio of 6 inches (150 mm) to 1 ⁄ 4 inch (6.4 mm), corresponding to an f /24 f-stop: In every lens there is, corresponding to a given apertal ratio (that is, the ratio of the diameter of the stop to the focal length), a certain distance of a near object from it ...

  6. List of unusual units of measurement - Wikipedia

    en.wikipedia.org/wiki/List_of_unusual_units_of...

    A board foot is a United States and Canadian unit of approximate volume, used for lumber. It is equivalent to 1 inch × 1 foot × 1 foot (144 cu in or 2,360 cm 3). It is also found in the unit of density pounds per board foot. In Australia and New Zealand the terms super foot or superficial foot were formerly used for this unit. The exact ...

  7. Aspect ratio (image) - Wikipedia

    en.wikipedia.org/wiki/Aspect_ratio_(image)

    A good example of this a 4×6 print (6 inch wide by 4 inch tall landscape) perfectly matches the 3:2 aspect ratio of a DSLR/35 mm, since 6/2=3 and 4/2=2. For analog projection of photographic slides, projector and screen use a 1:1 aspect ratio, supporting horizontal and vertical orientation equally well.

  8. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

  9. Display size - Wikipedia

    en.wikipedia.org/wiki/Display_size

    The size of a screen is usually described by the length of its diagonal, which is the distance between opposite corners, typically measured in inches. It is also sometimes called the physical image size to distinguish it from the "logical image size," which describes a screen's display resolution and is measured in pixels .