enow.com Web Search

  1. Ads

    related to: 1/16 inch to mm conversion chart

Search results

  1. Results from the WOW.Com Content Network
  2. Metric drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    For Morse taper-shank drill bits, the standard continues in 1/64 inch increments up to 1¾ inch, then 1/32 inch increments up to 2¼ inch, 1/16 inch increments up to 3 inches, 1/8 inch increments up to 3¼ inches, and a single 1/4 inch increment to 3½ inches. One aspect of this method of sizing is that the size increment between drill bits ...

  3. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Schematic of a machine tap. Below is a comprehensive drill and tap size chart for all drills and taps, imperial and metric, up to 36.5 millimetres (1.44 in) in diameter.. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

  4. French catheter scale - Wikipedia

    en.wikipedia.org/wiki/French_catheter_scale

    [1] The Charrière is measured by the ''outer'' diameter, and is defined as 1 Fr = 1/3 mm, and thus 1 mm = 3 Fr; therefore the diameter of a round catheter in millimetres can be determined by dividing the French size by 3. [2] The French units roughly correspond to the outer circumference of the catheter (see table below).

  5. List of scale model sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_scale_model_sizes

    Exact HO scale (half O of 7 mm = 1 foot) 1:87: 3.503 mm: Model railways (HO/h0) Civilian and military vehicles. Often used to describe HO scale. Original nominal 25 mm figure scale; though a 6-foot human in 1:87 is closer to 21 mm. 1:82: 3.717 mm An intermediate scale (HO/OO) intended to apply to both HO and OO scale train sets.

  6. Wrench size - Wikipedia

    en.wikipedia.org/wiki/Wrench_size

    Sizes that may interchange, depending on the precision needed, include 2 mm (close to 5 ⁄ 64 inch (1.98 mm)), 4 mm (close to 5 ⁄ 32 inch (3.97 mm)) and 8 mm (close to 5 ⁄ 16 inch (7.94 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

  7. List of rail transport modelling scale standards - Wikipedia

    en.wikipedia.org/wiki/List_of_rail_transport...

    H0 or 3.5 mm: 1:87: 16.5 mm (0.65 in) H0 scale was introduced in Britain in the 1920s, and although it stayed as the most common worldwide modelling scale, in Britain H0 has little commercial availability and is generally only used to model the British prototype by a small number of modellers. 00 or 4 mm: 1:76: 16.5 mm (0.65 in)

  8. AOL Mail

    mail.aol.com

    Get AOL Mail for FREE! Manage your email like never before with travel, photo & document views. Personalize your inbox with themes & tabs. You've Got Mail!

  9. Ring size - Wikipedia

    en.wikipedia.org/wiki/Ring_size

    Originally in 1945, the divisions were based on the ring inside diameter in steps of 1 ⁄ 64 inch (0.40 mm). [6] However, in 1987 BSI updated the standard to the metric system so that one alphabetical size division equals 1.25 mm of circumferential length. For a baseline, ring size C has a circumference of 40 mm. [7]

  1. Ads

    related to: 1/16 inch to mm conversion chart