enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Key (engineering) - Wikipedia

   en.wikipedia.org/wiki/Key_(engineering)

   Square keys are used for smaller shafts and rectangular faced keys are used for shaft diameters over 6.5 in (170 mm) or when the wall thickness of the mating hub is an issue. Set screws often accompany parallel keys to lock the mating parts into place. [3] The keyway is a longitudinal slot in both the shaft and mating part.

3. Keyway - Wikipedia

   en.wikipedia.org/wiki/Keyway

   Keyway may refer to: A part of a keyed joint used to connect a rotating machine element to a shaft; see key (engineering) A keyhole , a hole or aperture (as in a door or lock) for receiving a key; see lock and key

4. Engineering fit - Wikipedia

   en.wikipedia.org/wiki/Engineering_fit

   Engineering fits are generally used as part of geometric dimensioning and tolerancing when a part or assembly is designed. In engineering terms, the "fit" is the clearance between two mating parts, and the size of this clearance determines whether the parts can, at one end of the spectrum, move or rotate independently from each other or, at the other end, are temporarily or permanently joined.

5. Shaft (mechanical engineering) - Wikipedia

   en.wikipedia.org/wiki/Shaft_(mechanical_engineering)

   25 mm to 60 mm with 5 mm steps; 60 mm to 110 mm with 10 mm steps; 110 mm to 140 mm with 15 mm steps; 140 mm to 500 mm with 20 mm steps; The standard lengths of the shafts are 5 m, 6 m and 7 m. Usually 1m to 5m is used.

6. List of DIN standards - Wikipedia

   en.wikipedia.org/wiki/List_of_DIN_standards

   ISO general purpose metric screw threads – Part 9: Nominal sizes for 4 mm fine pitch threads; nominal diameter from 40 mm to 300 mm: Active: DIN 13-10: ISO general purpose metric screw threads – Part 10: Nominal sizes for 6 mm fine pitch threads; nominal diameter from 70 mm to 500 mm: Active: DIN 13-11: ISO general purpose metric screw ...

7. Broaching (metalworking) - Wikipedia

   en.wikipedia.org/wiki/Broaching_(metalworking)

   Also, there are limits on the size of internal cuts. Common internal holes can range from 0.125 to 6 in (3.2 to 152.4 mm) in diameter but it is possible to achieve a range of 0.05 to 13 in (1.3 to 330.2 mm). Surface broaches' range is usually 0.075 to 10 in (1.9 to 254.0 mm), although the feasible range is 0.02 to 20 in (0.51 to 508.00 mm).

8. Preferred metric sizes - Wikipedia

   en.wikipedia.org/wiki/Preferred_metric_sizes

   A standard metric (concrete) block is 190 mm wide, 390 mm long, and 190 mm high, which allows for 10 mm mortar joints in between bricks, giving a standard unit size of 200 mm square by 400 mm long. [3] A standard metric brick is 90 by 57 by 190 mm; with 10 mm of mortar, that produces a standard unit of 100 mm x 200 mm. [3]

9. Drill bit shank - Wikipedia

   en.wikipedia.org/wiki/Drill_bit_shank

   For example, this allows a 1 ⁄ 2-inch (13 mm) bit to be used in a pistol-grip drill's 3 ⁄ 8-inch (9.5 mm) chuck. One particular type of reduced-shank drill bits are Silver & Deming ( S&D ) bits, whose sets run from 9 ⁄ 16 -inch (14 mm) to 1 + 1 ⁄ 2 -inch (38 mm) drill body diameter with a standard 1 ⁄ 2 -inch (13 mm) reduced shank for ...