enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Example (inch, fine): For 7 ⁄ 16-20 (same diameter as the previous example, but this time with 20 threads per inch, which is considered fine), 0.437 in × 0.90 = 0.393 in (i.e., if the threads are to be fine, then a slightly larger diameter drill bit should be used before tapping the hole for the screw).

3. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   In 1913, Woolley and Meredith defined them like Anthony, but gave the following dimensions: hex head cap screws up to and including 7 ⁄ 16 inch (11.1125 mm) have a head that is 3 ⁄ 16 inch (4.7625 mm) larger than the shank diameter; screws greater than 1 ⁄ 2 inch (12.7 mm) in diameter have a head that is 1 ⁄ 4 inch (6.35 mm) larger than ...

4. Tap and die - Wikipedia

   en.wikipedia.org/wiki/Tap_and_die

   A comprehensive reference for US tap and drill bit sizes can be found in the chart provided by Albany County Fasteners. This chart includes detailed specifications for machine screw size, threads per inch, major and minor diameters, and appropriate drill sizes for different materials.

5. Drill bit shank - Wikipedia

   en.wikipedia.org/wiki/Drill_bit_shank

   Such a drill bit is called a reduced-shank or blacksmith's drill. For example, this allows a 1 ⁄ 2 -inch (13 mm) bit to be used in a pistol-grip drill's 3 ⁄ 8 -inch (9.5 mm) chuck. One particular type of reduced-shank drill bits are Silver & Deming ( S&D ) bits, whose sets run from 9 ⁄ 16 -inch (14 mm) to 1 + 1 ⁄ 2 -inch (38 mm) drill ...

6. List of screw drives - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_drives

   It typically consists of a countersunk flat-head bolt, with a thin shank and hex head protruding from the flat head. The hex head is used to drive the bolt into the countersunk hole, then either a wrench or hammer is used to break the shank and hex head from the flat head, or it is driven until the driving head shears off.

7. Drill bit - Wikipedia

   en.wikipedia.org/wiki/Drill_bit

   While the above is a common use of center drill bits, it is a technically incorrect practice and should not be considered for production use. The correct tool to start a traditionally drilled hole (a hole drilled by a high-speed steel (HSS) twist drill bit) is a spotting drill bit (or a spot drill bit, as they are referenced in the U.S.). The ...

8. Pilot hole - Wikipedia

   en.wikipedia.org/wiki/Pilot_hole

   For common wood screws, the pilot providing clearance for the core of the screw may be followed by a larger bit to shallower depth to provide clearance for the larger, unthreaded shank of the screw. For standard wood screws, special pilot drill bits are manufactured to produce the correct hole profile in a single operation, rather than needing ...

9. Drill bit sizes - Wikipedia

   en.wikipedia.org/wiki/Drill_bit_sizes

   ANSI B94.11M-1979 sets size standards for jobber-length straight-shank twist drill bits from 1/64 inch through 1 inch in 1/64 inch increments. For Morse taper -shank drill bits, the standard continues in 1/64 inch increments up to 1¾ inch, then 1/32 inch increments up to 2¼ inch, 1/16 inch increments up to 3 inches, 1/8 inch increments up to ...