enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. French catheter scale - Wikipedia

    en.wikipedia.org/wiki/French_catheter_scale

    The Charrière is measured by the ''outer'' diameter, and is defined as 1 Fr = 1/3 mm, and thus 1 mm = 3 Fr; therefore the diameter of a round catheter in millimetres can be determined by dividing the French size by 3. [2] The French units roughly correspond to the outer circumference of the catheter (see table below).

  3. Approximations of π - Wikipedia

    en.wikipedia.org/wiki/Approximations_of_π

    The bill was nearly passed by the Indiana General Assembly in the U.S., and has been claimed to imply a number of different values for π, although the closest it comes to explicitly asserting one is the wording "the ratio of the diameter and circumference is as five-fourths to four", which would make π = 16 ⁄ 5 = 3.2, a discrepancy of ...

  4. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

  5. Circular mil - Wikipedia

    en.wikipedia.org/wiki/Circular_mil

    As a unit of area, the circular mil can be converted to other units such as square inches or square millimetres. 1 circular mil is approximately equal to: 0.7854 square mils (1 square mil is about 1.273 circular mils) 7.854 × 10 −7 square inches (1 square inch is about 1.273 million circular mils) 5.067 × 10 −10 square metres

  6. Orders of magnitude (length) - Wikipedia

    en.wikipedia.org/wiki/Orders_of_magnitude_(length)

    Maximum diameter of Thiomargarita namibiensis, the second largest bacterium ever discovered 10 −3: 1 millimeter ~5 mm Length of an average flea is 1–10 mm (usually <5 mm) [27] 2.54 mm One-tenth inch; distance between pins in DIP (dual-inline-package) electronic components 5.70 mm Diameter of the projectile in 5.56×45mm NATO ammunition 10 −2

  7. Nominal Pipe Size - Wikipedia

    en.wikipedia.org/wiki/Nominal_Pipe_Size

    Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

  8. List of online map services - Wikipedia

    en.wikipedia.org/wiki/List_of_online_map_services

    Spanish official cartography website, including National Topographic Maps MTN50 (1:50,000 scale) and MTN25 (1:25,000 scale). [6] SITPA-IDEAS , Asturias regional maps.

  9. List of unusual units of measurement - Wikipedia

    en.wikipedia.org/wiki/List_of_unusual_units_of...

    Following the so-called "quarter-girth formula" (the square of one quarter of the circumference in inches multiplied by 1 ⁄ 144 of the length in feet), the notional log is four feet in circumference, one inch of which yields the hoppus board foot, 1 foot yields the hoppus foot, and 50 feet yields a hoppus ton.