enow.com Web Search

  1. Ads

    related to: 3mm to standard size paper

Search results

  1. Results from the WOW.Com Content Network
  2. ISO 216 - Wikipedia

    en.wikipedia.org/wiki/ISO_216

    The standard defines the "A", "B" and "C" series of paper sizes, which includes the A4, the most commonly available paper size worldwide. Two supplementary standards, ISO 217 and ISO 269, define related paper sizes; the ISO 269 "C" series is commonly listed alongside the A and B sizes.

  3. Paper size - Wikipedia

    en.wikipedia.org/wiki/Paper_size

    The international paper size standard is ISO 216. It is based on the German DIN 476 standard for paper sizes. Each ISO paper size is one half of the area of the next larger size in the same series. ISO paper sizes are all based on a single aspect ratio of the square root of 2, or approximately 1:1.41421. There are different series, as well as ...

  4. Technical lettering - Wikipedia

    en.wikipedia.org/wiki/Technical_lettering

    Location of Central Lines – The nominal size (h) and the spacing between characters (a) shall be taken as the basis for defining the central line. Range of Nominal Sizes – The nominal size is typically one of the sequence 2.5 mm, 3.5 mm, 5 mm, 7 mm, 10 mm, 14 mm, 20 mm. Successive members of this sequence are approximately in a ratio of the ...

  5. Photo print sizes - Wikipedia

    en.wikipedia.org/wiki/Photo_print_sizes

    The alternative Super series, denoted SnR, nR Plus or nR+, has an aspect ratio of 3∶2 (or as close as possible) and thus provides a better fit for standard 135 film (35 mm) at sizes of 8 inches or above. 5R is twice the size of a 2R print, 6R twice the size of a 4R print and S8R twice the size of 6R. 4D/6D is a newer size for most consumer ...

  6. Point (typography) - Wikipedia

    en.wikipedia.org/wiki/Point_(typography)

    The steps between nominal sizes are based on a factor of √2 ≈ 1.414 in order to match ISO 216 paper sizes. Since the set of sizes includes thicknesses of 0.1 mm, 0.5 mm, 1 mm and 2 mm, there is also one of 0.35 mm which is almost exactly 1 pica point.

  7. ANSI/ASME Y14.1 - Wikipedia

    en.wikipedia.org/wiki/ANSI/ASME_Y14.1

    A size chart illustrating the ANSI sizes. In 1992, the American National Standards Institute adopted ANSI/ASME Y14.1 Decimal Inch Drawing Sheet Size and Format, [1] which defined a regular series of paper sizes based upon the de facto standard 8 + 1 ⁄ 2 in × 11 in "letter" size to which it assigned the designation "ANSI A".

  8. ISO 217 - Wikipedia

    en.wikipedia.org/wiki/ISO_217

    The sizes of the RA series are also slightly larger than corresponding inch-based US sizes specified in ANSI/ASME Y14.1, e.g. RA4 is roughly equivalent to 8 + 1 ⁄ 2 in × 12 in (220 mm × 300 mm) and ANSI A (alias US Letter) is defined as 8 + 1 ⁄ 2 in × 11 in (220 mm × 280 mm).

  9. Bleed (printing) - Wikipedia

    en.wikipedia.org/wiki/Bleed_(printing)

    A standard US bleed is 0.125", or one-eighth of an inch while a standard Australian bleed is 5mm. Die-cuts sometimes require a 1/4" bleed from where the page is intended to be cut; this is because of the possible movement of the paper during the die-cut procedure.

  1. Ads

    related to: 3mm to standard size paper