Search results
Results from the WOW.Com Content Network
Good short block prep with proper clearances (rod,main,rod side clearance piston gap etc). Vortec heads with a drop in spring kit or have the guides cut, .028" thick head gaskets and self aligning roller rockers. Retrofit hydro roller cam in the 220/ 230@.050 range 500ish lift, RPM airgap intake, 1-5/8" headers, 600-650cfm carb, good quality ...
TH350 Master Kit with Steels- $85 (This is the clutches, steels, gaskets, seals, o-rings, etc, it does NOT include a band, bushings, filter, modulator, seals, etc). Approximately $275 to my door in parts. I don't buy a prepackaged valve body kit or valve body, that's a $50 hit for most shops minimum.
I've got a Gen 1 small block 350 with the casting number 14093638 and the front stamp V0709USA. It currently has an Edelbrock 3704 tbi intake on it with 10088113 aluminum heads. The 4 inner bolt holes on the intake were, I assume, drilled out to fit the bolt angle on the heads by the previous owner. I'm currently looking to carb swap it and am ...
Jan 17, 2002. 823. TRAFFORD, PA. This can be looked at as part 2 of "I found a block". This is the 4-bolt 350 block I mentioned late in my previous thread. Code says 1401679, 4-bolt main, 010 stamped on front pad, timing chain area. Mortec and some others have this as a 77-79, 2 or 4-bolt (it is a four bolt). Would this be a good block to stroke.
Should be 2 set of characters, one it the engine code and the other the VIN derivative. Look something like the following. T1024TFD engine code If the first letter in the suffix is the letter T, its a truck engine. C its a car engine. 18N300001 VIN derivative 1 - Chevy, C - Chevy trucks, T - GMC trucks 8 - model year is 1968
3,201. pegram,tn.,cheatam. was the 70 z cam refered to as the .030- .030 cam or was that the 375 fuelly,that cam went 100,000+ miles in a 64chevelle ss 4 speed 283 (301)cu.in. back in my day, was a lot of fun but had no low end torke, would be side ways with the 308posi tell at 6000 rpm.,,small yellow line 14" tires,car was yellow so tires ...
I have a 400 small block in my 70 1/2 Camaro and I have a little problem with power. The engine shakes more than I would expect, because everything is mostly stock at this point. I started with the body work, then interior and now power train. In my troubleshooting, the first thing I noticed is the temperature of the exhaust header at the ...
Casting Date Small block casting date is located on driver side rear of block on flange forward of bellhousing. Big block on the right side of engine above the oil pan rails. Casting Date Example: E038 - (E = Month, 03 = Day, 8 = Last digit of model year (1978)). Month: A = Jan, B = Feb, C = Mar, D = Apr, E = May, F = Jun, G = July, H = Aug, I ...
Sep 14, 2007. 99. Montclair, VA. It is possible to safely use an engine with .010 piston skirt to sidewall clearance. It is most commonly done in race engines with some squeeze on them, and always will a good quality file fit ring. I wouldn't just hog out the bores with a hone and run a set of TRW off the shelf rings.
Optional high-performance engine supplied with flat top pistons, performance cam, 194 intake valve heads, and high volume oil pump" for $1012. They also offer a newer version with description of "Roller cam, 2-bolt main, block #880, head #906, valve cover bolts thru center of cover, plastic timing cover with crank sensor. Vortec" for $1649.