Search results
Results from the WOW.Com Content Network
225 mm 2 area Four Thirds System format from Olympus (crop factor 2.0) 116 mm 2 area 1" Nikon CX format used in Nikon 1 series [17] and Samsung mini-NX series (crop factor 2.7) 43 mm 2 area 1/1.7" Pentax Q7 (4.55 crop factor) 30 mm 2 area 1/2.3" original Pentax Q (5.6 crop factor). Current Q-series cameras have a crop factor of 4.55.
1:128: 3 ⁄ 32 in: 2.381 mm A few rockets and some fit-in-the-box aircraft are made to this size. 1:120: 0.1 in: 2.54 mm: Model railways (TT) Derived from the scale of 1 inch equals 10 feet.TT model railroad scale. Used in AD&D Battlesystem Skirmishes rules. Works with 15 mm miniatures where a 6 foot man would equal 15.24 mm 1:110: 2.771 mm
So a 1 / 2 in (12.7 mm) diameter drill will be able to drill a hole 4 + 1 / 2 in (114.3 mm) deep, since it is 9 times the diameter in length. A 1 / 8 in (3.175 mm) diameter drill can drill a hole 1 + 5 / 8 in (41.275 mm) deep, since it is 13 times the diameter in flute length. [3]
fps 2: ≡ 1 ft/s 2 = 3.048 × 10 −1 m/s 2: gal; galileo: Gal ≡ 1 cm/s 2 = 10 −2 m/s 2: inch per minute per second: ipm/s ≡ 1 in/(min⋅s) = 4.2 3 × 10 −4 m/s 2: inch per second squared: ips 2: ≡ 1 in/s 2 = 2.54 × 10 −2 m/s 2: knot per second: kn/s ≡ 1 kn/s ≈ 5.1 4 × 10 −1 m/s 2: metre per second squared (SI unit) m/s 2 ...
Thus, the outer diameter of a catheter in millimeters can be calculated by dividing the French size by 3. [2] For example, a catheter with a French size of 9 would have an outer diameter of approximately 3 mm. While the French scale aligns closely with the metric system, it introduces redundancy and the potential for rounding errors.
In addition, 10 mm (0.393 in), and letter X (0.397 in) will work well, although major minus pitch by itself does not tell you this; but the 90% ± 2 pp guideline supports it. For both of these rules of thumb (85%/90% and major minus pitch), the tap drill size yielded is not necessarily the only possible one, but it is a good one for general use.
The optical format is approximately the diagonal length of the sensor multiplied by 3/2. The result is expressed in inches and is usually (but not always) rounded to a convenient fraction. For instance, a 6.4x4.8 mm sensor has a diagonal of 8.0 mm and therefore an optical format of 8.0*3/2 = 12 mm, which is expressed as 1 ⁄ 2 inch in imperial ...
The alternative Super series, denoted SnR, nR Plus or nR+, has an aspect ratio of 3∶2 (or as close as possible) and thus provides a better fit for standard 135 film (35 mm) at sizes of 8 inches or above. 5R is twice the size of a 2R print, 6R twice the size of a 4R print and S8R twice the size of 6R. 4D/6D is a newer size for most consumer ...