enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. British Association screw threads - Wikipedia

    en.wikipedia.org/wiki/British_Association_screw...

    The major diameter is given by 6p 1.2, [4]: 12 rounded to two significant figures in mm and the hex head size (across the flats) is 1.75 times the major diameter. BA sizes are specified by the following British Standards: BS 57:1951 — B.A. screws, bolts and nuts

  3. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

  4. ISO metric screw thread - Wikipedia

    en.wikipedia.org/wiki/ISO_metric_screw_thread

    It indicates the diameter of smooth-walled hole that a male thread (e.g. on a bolt) will pass through easily to connect to an internally threaded component (e.g. a nut) on the other side. For example, an M6 screw has a nominal outer diameter of 6 millimetres and will therefore be a well-located, co-axial fit in a hole drilled to 6 mm diameter.

  5. Unified Thread Standard - Wikipedia

    en.wikipedia.org/wiki/Unified_Thread_Standard

    The standard designation for a UTS thread is a number indicating the nominal (major) diameter of the thread, followed by the pitch measured in threads per inch.For diameters smaller than ⁠ 1 / 4 ⁠ inch, the diameter is indicated by an integer number defined in the standard; for all other diameters, the inch figure is given.

  6. Drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    ANSI B94.11M-1979 sets size standards for jobber-length straight-shank twist drill bits from 1/64 inch through 1 inch in 1/64 inch increments. For Morse taper -shank drill bits, the standard continues in 1/64 inch increments up to 1¾ inch, then 1/32 inch increments up to 2¼ inch, 1/16 inch increments up to 3 inches, 1/8 inch increments up to ...

  7. British Standard Whitworth - Wikipedia

    en.wikipedia.org/wiki/British_Standard_Whitworth

    In the US, BSW was replaced when steel bolts replaced iron, but was still being used for some aluminium parts as late as the 1960s and 1970s when metric-based standards International Inch replaced the U.S. inch and U.K. inch in 1951-1964. [citation needed] American Unified Coarse (UNC) was originally based on almost the same Imperial fractions ...

  8. GM 10.5-inch 14-bolt differential - Wikipedia

    en.wikipedia.org/wiki/GM_10.5-inch_14-bolt...

    Many Wrangler owners will have up to two inches removed from the bottom of the 10.5" 14-bolt differential housing to maximize ground clearance. [9] The popularity of GM trucks and vans made 10.5" 14-bolt axles a common sight in junkyards, making them an option for vehicle customization projects, including buggy builds and even classic trucks.

  9. ASTM A325 - Wikipedia

    en.wikipedia.org/wiki/ASTM_A325

    ASTM A325 is an ASTM International standard for heavy hex structural bolts, titled Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength. It defines mechanical properties for bolts that range from 1 ⁄ 2 to 1 + 1 ⁄ 2 inches (13 to 38 mm) in diameter.