enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25).

3. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

4. Preferred metric sizes - Wikipedia

   en.wikipedia.org/wiki/Preferred_metric_sizes

   Machine screws with different thread diameters Hex key set with metric sizes from 2 mm to 10 mm according to sizes for use with ISO 262 screw sizes (except 3.5 mm for M6 internal set screw) For each size bolt or screw and type of head, there is a corresponding size driver prescribed by various ISO standards, including: Internal hex drive: ISO ...

5. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   ISO general purpose metric screw threads—General plan: V Thread Form: M6x1 ISO 262:1998: ISO general purpose metric screw threads—Selected sizes for screws, bolts and nuts: V Thread Form ISO 724:1993: ISO general-purpose metric screw threads—Basic dimensions: V Thread Form ISO 725:2009: ISO inch screw threads—Basic dimensions: V Thread ...

6. Computer case screws - Wikipedia

   en.wikipedia.org/wiki/Computer_case_screws

   The bottom M3 screw has a finer pitch than the top #6-32 UNC screw. The M3 is a metric screw specifying a nominal diameter of 3 millimetres (0.12 in); and standard coarse thread pitch defined as 0.5 millimetres (0.020 in). The M3 is the second most common screw found in PCs. [1] [self-published source?

7. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   In 1913, Woolley and Meredith defined them like Anthony, but gave the following dimensions: hex head cap screws up to and including 7 ⁄ 16 inch (11.1125 mm) have a head that is 3 ⁄ 16 inch (4.7625 mm) larger than the shank diameter; screws greater than 1 ⁄ 2 inch (12.7 mm) in diameter have a head that is 1 ⁄ 4 inch (6.35 mm) larger than ...

8. List of screw drives - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_drives

   In Japan, the male sizes are often designated as DTC-20, DTC-27, DTC-40 (discontinued) and DTC-45 corresponding to a respective screw head size of 3.2 mm, 4.6 mm, 6.4 mm and 7.7 mm; with the size of the screw measured across the widest portion of the mating part of the head. The most common sizes in use for consumer electronics are DTC-20 and ...

9. British Standard Pipe - Wikipedia

   en.wikipedia.org/wiki/British_Standard_Pipe

   British Standard Pipe Parallel Thread Dimensions; British Standard Pipe Taper Thread Dimensions Archived 2017-09-27 at the Wayback Machine; BSP Thread Charts and Diagrams, showing dimensions of tubing and fittings; ISO 7-1:1994; ISO 7-2:2000; ISO 228-1:2000; ISO 228-2:1987; Parallel pipe threads G; Parallel pipe threads PF