enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   ISO general purpose metric screw threads—General plan: V Thread Form: M6x1 ISO 262:1998: ISO general purpose metric screw threads—Selected sizes for screws, bolts and nuts: V Thread Form ISO 724:1993: ISO general-purpose metric screw threads—Basic dimensions: V Thread Form ISO 725:2009: ISO inch screw threads—Basic dimensions: V Thread ...

3. Thread angle - Wikipedia

   en.wikipedia.org/wiki/Thread_angle

   Acme thread [6] 29° ASME/ANSI B1.5-1988 [7] Metric trapezoidal threads [1] Tr 30° DIN 103 Buttress threads [6] S 45° DIN 2781 German buttress threads [6] S 30° DIN 513 Square threads [1] Sq 0° (parallel) ? Panzergewinde, "steel conduit thread" Pg 80° DIN 40430 British Association (BA) thread: BA 47° 30' = 47.5° BS 93:2008 Löwenherz ...

4. Trapezoidal thread form - Wikipedia

   en.wikipedia.org/wiki/Trapezoidal_thread_form

   The trapezoidal metric thread form is similar to the Acme thread form, except the thread angle is 30°. [ 4 ] [ 5 ] [ 6 ] It is codified by DIN 103. [ 7 ] While metric screw threads are more prevalent worldwide than imperial threads for triangular thread forms, the imperially sized Acme threads predominate in the trapezoidal thread form.

5. Screw thread - Wikipedia

   en.wikipedia.org/wiki/Screw_thread

   The nominal diameter of Metric (e.g. M8) and Unified (e.g. 5 ⁄ 16 in) threads is the theoretical major diameter of the male thread, which is truncated (diametrically) by 0.866 ⁄ 4 of the pitch from the dimension over the tips of the "fundamental" (sharp cornered) triangles.

6. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   The standard designation for a UTS thread is a number indicating the nominal (major) diameter of the thread, followed by the pitch measured in threads per inch.For diameters smaller than ⁠ 1 / 4 ⁠ inch, the diameter is indicated by an integer number defined in the standard; for all other diameters, the inch figure is given.

7. Propane, butane, and LPG container valve connections

   en.wikipedia.org/wiki/Propane,_butane,_and_LPG...

   The designation used for international ISO metric screw threads. BSP ... Nominal diameter (inch) Pitch (TPI) ... No thread 1 1/4" x 5 ACME LH (G.30) EN 15202

8. Width across flats - Wikipedia

   en.wikipedia.org/wiki/Width_across_flats

   The table below shows dimensions of metric spanners for selected sizes of metric threads. [2] Note that with ISO 272 1982 the width across flats for M10, M12, M14 and M22 were changed from 17, 19, 22 and 32 mm respectively to the current standard.

9. Barrel threads - Wikipedia

   en.wikipedia.org/wiki/Barrel_threads

   *The final part of the shank has its diameter reduced to 22.86 mm. 1"-14 M1 Garand, M14, M1A Tr25.40: 2.540 mm 29° ACME trapezoidal threads. 24.66 mm-0.13 mm major diameter, 23.19 mm- 0.13 mm minor diameter, 1.32 mm-0.08 mm average thread width. Internal radius of 0.25 mm, external radius of 0.13 mm.