Ads
related to: high-pinion dana 70 (new gm version) 3 boltebay.com has been visited by 1M+ users in the past month
- Electronics
From Game Consoles to Smartphones.
Shop Cutting-Edge Electronics Today
- eBay Money Back Guarantee
Worry-Free Shopping.
eBay Is Here For You!
- Sporting Goods
Are You Ready to Play Like a Pro?
eBay Has Outstanding Gear For You!
- Business & Industrial
From Construction to Catering.
eBay Has All B&I Products For You.
- Electronics
walmart.com has been visited by 1M+ users in the past month
Search results
Results from the WOW.Com Content Network
The Dana 70 rear axle was first used in the Dodge W300 in 1958. The Dana 70 started out using 10 spline pinions and 23 spline axle shafts. The later, more current, Dana 70 axles use 29 spline pinions and 32 or 35 spline axle shafts. Dana offered two different limited slip differentials with the Dana 70, the "Powr-Lok" and the "Trac-Lok."
A rear wheel drive bellhousing is displayed at right, and the integrated front wheel drive bellhousing is displayed at the lower right (in this case, as a part of the GM 6T70 Transmission). GM 60-Degree 2.8/3.1/3.4/3.5/3.9 L V6 (also used by AMC) Buick 3300/3800 V6; Cadillac HT4100/4.5/4.9 L V8; Isuzu all 3.2 and 3.5L DOHC V6
The GM AAM axle tubes exhibit a smaller diameter at the spindle compared to the AAM Dodge axles—measuring 4" for GM and 3.5" for Dodge from the housing. In design variation, newer GM trucks are aligned with Dodge axles. Additionally, GM incorporates a vibration damper on the yoke, while Dodge positions it on the drive shaft.
The GM 9.25 IFS has been the main front differential in Four-wheel drive 3/4 Ton and 1 Ton GM trucks since 1988. The Dana 60 solid axle front end was used selectively in trucks with a higher GVWR from 1988 to 1991. The original Saginaw 9.5 differential, ring and pinion were modified to work with the independent front suspension.
Dana 44 Front axles were known for utilizing locking hubs or a center axle disconnect system. However, a permanently locked-in Dana 44 is not uncommon. The Dana 44 has seen use in 1/4-, 1/2-, 3/4-, and 1-ton rated trucks. The Dana 44 was manufactured in kingpin and ball joint variations, as well as closed and open knuckle variations.
The Dana 50 has a "50" cast into the housing and is regarded to have more strength than a Dana 44, but not as much as a Dana 60. It was only produced in a reverse cut gear set aka a high pinion. The Dana 50 was made as a solid axle and as a Twin Traction Beam (TTB) which pivots in the center allowing the wheels to move independently of each ...
The first version was produced from 1985 to 1992. The second version, produced from 1993 to 1997 featured a stronger pinion/yoke. This corrected a known, but rare, issue of the pinion yoke nut working loose. The first and second versions of the 10.25 axle are colloquially known as “short pinion-yoke” and “long pinion-yoke” respectively.
Dana 80's are made as full floating, rear axles only and are a step up in overall strength compared to the Dana 70. 1988 Ford was the first company to use the Dana 80. The Dana 80 has a GAWR up to 11,000 pounds (5,000 kg), however it is common practice among manufacturers to derate Dana 80's. Gross axle weight ratings are lowered by the vehicle ...
Ads
related to: high-pinion dana 70 (new gm version) 3 boltebay.com has been visited by 1M+ users in the past month
walmart.com has been visited by 1M+ users in the past month