enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. British Association screw threads - Wikipedia

   en.wikipedia.org/wiki/British_Association_screw...

   BS 93:2008 — British Association (B.A.) screw threads — Requirements. The angle of the thread is 47.5° [4]: 2 and the depth of thread is 0.6 times the pitch with rounded tops and bottoms. Thus, the shortening at the crest and root is given by 0.26817 p with a radius of 0.18083 p at both crest and root. [4]: 2 The 1884 report specifies a ...

3. Poly(methyl methacrylate) - Wikipedia

   en.wikipedia.org/wiki/Poly(methyl_methacrylate)

   Poly (methyl methacrylate) (PMMA) is the synthetic polymer derived from methyl methacrylate. It is used as an engineering plastic, and it is a transparent thermoplastic. PMMA is also known as acrylic, acrylic glass, as well as by the trade names and brands Crylux, Hesalite, Plexiglas, Acrylite, Lucite, and Perspex, among several others (see below).

4. Nominal Pipe Size - Wikipedia

   en.wikipedia.org/wiki/Nominal_Pipe_Size

   Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

5. ANSI/ASME Y14.1 - Wikipedia

   en.wikipedia.org/wiki/ANSI/ASME_Y14.1

   A size chart illustrating the ANSI sizes. In 1992, the American National Standards Institute adopted ANSI/ASME Y14.1 Decimal Inch Drawing Sheet Size and Format, [1] which defined a regular series of paper sizes based upon the de facto standard 8 + 1 ⁄ 2 in × 11 in "letter" size to which it assigned the designation "ANSI A".

6. Mesh (scale) - Wikipedia

   en.wikipedia.org/wiki/Mesh_(scale)

   e. Mesh is a measurement of particle size often used in determining the particle-size distribution of a granular material. For example, a sample from a truckload of peanuts may be placed atop a mesh with 5 mm openings. When the mesh is shaken, small broken pieces and dust pass through the mesh while whole peanuts are retained on the mesh.

7. Sheet metal - Wikipedia

   en.wikipedia.org/wiki/Sheet_metal

   Microscopic close-up of mild steel sheet metal. Sheet metal is metal formed into thin, flat pieces, usually by an industrial process. Thicknesses can vary significantly; extremely thin sheets are considered foil or leaf, and pieces thicker than 6 mm (0.25 in) are considered plate, such as plate steel, a class of structural steel. Sheet metal is ...

8. Computer case screws - Wikipedia

   en.wikipedia.org/wiki/Computer_case_screws

   The #6-32 UNC screw has a thread pitch of 1/32 in (0.031250 inches (0.7938 mm)).. The #6-32 UNC is a UTS screw specifying a major thread diameter of #6 which is defined as 0.1380 inches (3.51 mm); and 32 tpi (threads per inch) which equates to a thread pitch of 0.031250 inches (0.7938 mm).

9. Sheet resistance - Wikipedia

   en.wikipedia.org/wiki/Sheet_resistance

   The reason for the name "ohms per square" is that a square sheet with sheet resistance 10 ohm/square has an actual resistance of 10 ohm, regardless of the size of the square. (For a square, =, so =.) The unit can be thought of as, loosely, "ohms · aspect ratio". Example: A 3-unit long by 1-unit wide (aspect ratio = 3) sheet made of material ...