enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. Drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    Drill bit sizes are written as irreducible fractions. So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a chart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths).

  3. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

  4. Wrench size - Wikipedia

    en.wikipedia.org/wiki/Wrench_size

    Sizes that may interchange, depending on the precision needed, include 2 mm (close to 5 ⁄ 64 inch (1.98 mm)), 4 mm (close to 5 ⁄ 32 inch (3.97 mm)) and 8 mm (close to 5 ⁄ 16 inch (7.94 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

  5. Template:Convert/list of units/length/short list - Wikipedia

    en.wikipedia.org/wiki/Template:Convert/list_of...

    ftin (feet and inches) ft m (foot m) inch: in in Use of ′ and ″ symbols violates MOSNUM so is not provided. 1.0 in (25 mm) in cm; in mm; Other: nautical mile: nmi nmi the international standard nautical mile For other nautical miles see the full list. 1.0 nmi (1.9 km; 1.2 mi) parsec: pc pc 1.0 pc (3.3 ly) light-year: ly ly 1.0 ly (63,000 AU ...

  6. Inch - Wikipedia

    en.wikipedia.org/wiki/Inch

    Subdivisions of an inch are typically written using dyadic fractions with odd number numerators; for example, two and three-eighths of an inch would be written as ⁠2 + 3 / 8 ⁠ ″ and not as 2.375″ nor as ⁠2 + 6 / 16 ⁠ ″. However, for engineering purposes fractions are commonly given to three or four places of decimals and have been ...

  7. List of scale model sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_scale_model_sizes

    Original nominal 25 mm figure scale; though a 6-foot human in 1:87 is closer to 21 mm. 1:82: 3.717 mm An intermediate scale (HO/OO) intended to apply to both HO and OO scale train sets. Also used for some military models 1:80: 3.810 mm HOj scale. Very close to wargaming 20 mm figure scale (20 mm is actually 1:80.5). [10] 1:76.2: 4 mm: Model ...

  8. Mesh (scale) - Wikipedia

    en.wikipedia.org/wiki/Mesh_(scale)

    For example, a sample from a truckload of peanuts may be placed atop a mesh with 5 mm openings. When the mesh is shaken, small broken pieces and dust pass through the mesh while whole peanuts are retained on the mesh. A commercial peanut buyer might use a test like this to determine if a batch of peanuts has too many broken pieces.

  9. Help:Convert - Wikipedia

    en.wikipedia.org/wiki/Help:Convert

    By default, the output value is rounded to adjust its precision to match that of the input. An input such as 1234 is interpreted as 1234 ± 0.5, while 1200 is interpreted as 1200 ± 50, and the output value is displayed accordingly, taking into account the scale factor used in the conversion.