enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Schematic of a machine tap. Below is a comprehensive drill and tap size chart for all drills and taps, imperial and metric, up to 36.5 millimetres (1.44 in) in diameter.. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

  3. ISO metric screw thread - Wikipedia

    en.wikipedia.org/wiki/ISO_metric_screw_thread

    It indicates the diameter of smooth-walled hole that a male thread (e.g. on a bolt) will pass through easily to connect to an internally threaded component (e.g. a nut) on the other side. For example, an M6 screw has a nominal outer diameter of 6 millimetres and will therefore be a well-located, co-axial fit in a hole drilled to 6 mm diameter.

  4. Computer case screws - Wikipedia

    en.wikipedia.org/wiki/Computer_case_screws

    The bottom M3 screw has a finer pitch than the top #6-32 UNC screw. The M3 is a metric screw specifying a nominal diameter of 3 millimetres (0.12 in); and standard coarse thread pitch defined as 0.5 millimetres (0.020 in). The M3 is the second most common screw found in PCs. [1] [self-published source?

  5. List of screw and bolt types - Wikipedia

    en.wikipedia.org/wiki/List_of_screw_and_bolt_types

    Nominal (thread) sizes range from 0.1875 to 0.375 in (4.763 to 9.525 mm) and lengths from 1.25 to 5 in (32 to 127 mm). Typically an installer uses a hammer drill to make a pilot hole for each concrete screw and a powered impact driver to drive the screw. The drill hole should be 1/2" longer than the depth penetration of the screw.

  6. Tap and die - Wikipedia

    en.wikipedia.org/wiki/Tap_and_die

    where is the tap drill size, is the major diameter of the tap (e.g., 10 mm for a M10×1.5 tap), and pitch is the pitch of the thread (1.5 mm in the case of a standard M10 tap) and so the correct drill size is 8.5 mm. This works for both fine and coarse pitches, and also produces an approximate 75% thread.

  7. Cage nut - Wikipedia

    en.wikipedia.org/wiki/Cage_nut

    A common use for cage nuts is to mount equipment in square-holed 19-inch racks (the most common type), with 0.375 inches (9.5 mm) square-hole size. There are four common sizes: UNF 10–32 and, to a lesser extent, UNC 12–24 are generally used in the United States; elsewhere, M5 (5 mm outside diameter and 0.8 mm pitch) for light and medium equipment and M6 for heavier equipment, such as servers.

  8. Drill bit - Wikipedia

    en.wikipedia.org/wiki/Drill_bit

    A Forstner bit could bore the mounting hole for the hinge, but particle board and MDF are very abrasive materials, and steel cutting edges soon wear. A tungsten carbide cutter is needed, but the complex shape of a forstner bit is difficult to manufacture in carbide, so this special drill bit with a simpler shape is commonly used.

  9. Pilot hole - Wikipedia

    en.wikipedia.org/wiki/Pilot_hole

    to guide a larger drill to the appropriate location and ease the job of the larger drill, allow the insertion of another hole-making tool, such as a knockout punch, that will produce the final-sized hole, or; locate, guide, and provide clearance for a self-threading screw in wood or plastic to prevent damaging the material or breaking the screw.