enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

  3. Drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    ANSI B94.11M-1979 sets size standards for jobber-length straight-shank twist drill bits from 1/64 inch through 1 inch in 1/64 inch increments. For Morse taper -shank drill bits, the standard continues in 1/64 inch increments up to 1¾ inch, then 1/32 inch increments up to 2¼ inch, 1/16 inch increments up to 3 inches, 1/8 inch increments up to ...

  4. Ring size - Wikipedia

    en.wikipedia.org/wiki/Ring_size

    Originally in 1945, the divisions were based on the ring inside diameter in steps of 1 ⁄ 64 inch (0.40 mm). [6] However, in 1987 BSI updated the standard to the metric system so that one alphabetical size division equals 1.25 mm of circumferential length. For a baseline, ring size C has a circumference of 40 mm. [7]

  5. Fid - Wikipedia

    en.wikipedia.org/wiki/Fid

    A one-half-inch (12.7 mm) diameter rope would have any accompanying fid 10.5–11 in (266.7–279.4 mm) in length with hash-marks denoting the long and short fid measurements. A short fid is 1 ⁄ 3 a fid length and a long fid is 2 ⁄ 3 the overall fid length.

  6. Nominal Pipe Size - Wikipedia

    en.wikipedia.org/wiki/Nominal_Pipe_Size

    Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

  7. French catheter scale - Wikipedia

    en.wikipedia.org/wiki/French_catheter_scale

    The French scale, also known as the French gauge or Charrière system, is a widely used measurement system for the size of catheters.It is commonly abbreviated as Fr but may also be abbreviated as Fg, FR or F, and less frequently as CH or Ch (referencing its inventor, Charrière).

  8. Conversion of units - Wikipedia

    en.wikipedia.org/wiki/Conversion_of_units

    Conversion of units is the conversion of the unit of measurement in which a quantity is expressed, typically through a multiplicative conversion factor that changes the unit without changing the quantity.

  9. Rack unit - Wikipedia

    en.wikipedia.org/wiki/Rack_unit

    Rack with sample component sizes including an A/V half-rack unit. A rack unit (abbreviated U or RU) is a unit of measure defined as 1 + 3 ⁄ 4 inches (44.45 mm). [1] [2] It is most frequently used as a measurement of the overall height of 19-inch and 23-inch rack frames, as well as the height of equipment that mounts in these frames, whereby the height of the frame or equipment is expressed ...