enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25). If the pitch is the normally used "coarse" pitch listed in ISO 261 or ...

3. Preferred metric sizes - Wikipedia

   en.wikipedia.org/wiki/Preferred_metric_sizes

   Machine screws with different thread diameters Hex key set with metric sizes from 2 mm to 10 mm according to sizes for use with ISO 262 screw sizes (except 3.5 mm for M6 internal set screw) For each size bolt or screw and type of head, there is a corresponding size driver prescribed by various ISO standards, including: Internal hex drive: ISO ...

4. Width across flats - Wikipedia

   en.wikipedia.org/wiki/Width_across_flats

   A few sizes are close enough to interchange for most purposes, such as 19 mm (close to 3 ⁄ 4 inch (19.05 mm)), 8 mm (close to 5 ⁄ 16 inch (7.94 mm)) and 4 mm (close to 5 ⁄ 32 inch (3.97 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

5. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Below is a comprehensive drill and tap size chart for all drills and taps: Inch, imperial, and metric, up to 36.5 millimetres (1.44 in) in diameter. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

6. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   Hose Coupling Screw Threads - Inch: Pipe Thread Form ASME B1.21M-1997 (R2013) Metric Screw Threads - MJ Profile: V Thread Form BS 84: Tables of BS Whitworth, BS Fine and BS Pipe Threads: V Thread Form (55°) 1 ⁄ 4 ″-20 BSW ISO 68-1:1998: ISO general purpose screw threads—Basic profile—Part 1: Metric screw threads: V Thread Form ISO 68-2 ...

7. ISO 965 - Wikipedia

   en.wikipedia.org/wiki/ISO_965

   ISO 965 (ISO general purpose metric screw thread—tolerances) is an International Organization for Standardization (ISO) standard for metric screw thread tolerances. [1] It specifies the basic profile for ISO general purpose metric screw threads (M) conforming to ISO 261. [2] The tolerance system refers to the basic profile in accordance with ...

8. List of DIN standards - Wikipedia

   en.wikipedia.org/wiki/List_of_DIN_standards

   ISO general purpose metric screw threads – Part 12: 1 to 300 mm diameter coarse and fine pitch threads Selected diameters and pitches: Active: DIN 13-13: ISO general purpose metric screw threads – Part 13: Selected sizes for screws, bolts and nuts from 1 to 52 mm screw thread diameter and limits of sizes: Active: DIN 13-19

9. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   The screw itself should be drilled a minimum of 1" into the concrete to hold effectively and a maximum of 1-3/4" or the threads will wear and will lose holding power. Ideally 1-1/4" to 1-1/2" of screw thread in the concrete. [1] So for example, if a 1/2" board is being screwed onto the concrete, a 1-3/4" to 2" concrete screw should be used ...