enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Example (inch, fine): For 7 ⁄ 16-20 (same diameter as the previous example, but this time with 20 threads per inch, which is considered fine), 0.437 in × 0.90 = 0.393 in (i.e., if the threads are to be fine, then a slightly larger diameter drill bit should be used before tapping the hole for the screw).

3. Drill - Wikipedia

   en.wikipedia.org/wiki/Drill

   A drill press Drill press (then called a boring machine) boring wooden reels for winding barbed wire, 1917. A drill press (also known as a pedestal drill, pillar drill, or bench drill) is a style of drill that may be mounted on a stand or bolted to the floor or workbench. Portable models are made, some including a magnetic base.

4. Boring (manufacturing) - Wikipedia

   en.wikipedia.org/wiki/Boring_(manufacturing)

   A part's-eye view of a boring bar. Hole types: Blind hole (left), through hole (middle), interrupted hole (right). In machining, boring is the process of enlarging a hole that has already been drilled (or cast) by means of a single-point cutting tool (or of a boring head containing several such tools), such as in boring a gun barrel or an engine cylinder.

5. Chuck (engineering) - Wikipedia

   en.wikipedia.org/wiki/Chuck_(engineering)

   A drill chuck is a specialised self-centering, three-jaw chuck, usually with capacity of 0.5 in (13 mm) or less, and rarely greater than 1 in (25 mm), used to hold drill bits or other rotary tools. This type of chuck is used on tools ranging from professional equipment to inexpensive hand and power drills for domestic use.

6. Drill bit shank - Wikipedia

   en.wikipedia.org/wiki/Drill_bit_shank

   One particular type of reduced-shank drill bits are Silver & Deming (S&D) bits, whose sets run from 9 ⁄ 16-inch (14 mm) to 1 + 1 ⁄ 2-inch (38 mm) drill body diameter with a standard 1 ⁄ 2-inch (13 mm) reduced shank for all. This allows drill presses with 1 ⁄ 2-inch (13 mm) chucks to run the larger drills. S&D bits are 6 inches (150 mm ...

7. Drill bit sizes - Wikipedia

   en.wikipedia.org/wiki/Drill_bit_sizes

   Fractional drill bit set by Craftsman. Fractional-inch drill bit sizes are still in common use in the United States and in any factory (around the globe) that makes inch-sized products for the U.S. market. ANSI B94.11M-1979 sets size standards for jobber-length straight-shank twist drill bits from 1/64 inch through 1 inch in 1/64 inch increments.

8. Set screw - Wikipedia

   en.wikipedia.org/wiki/Set_screw

   On a shaft, this may be simply a flattened area. A set screw may have any type of drive, such as hex or square head, slot, or recessed --- cross (Phillips), hex (Allen), star (Torx), or square (Robertson). In the UK, the term "set screw" or "setscrew" refers simply to a bolt which is fully threaded, with no smooth shank; called cap screw in the US.

9. List of components of oil drilling rigs - Wikipedia

   en.wikipedia.org/wiki/List_of_components_of_oil...

   Drill bit (#26) is a device attached to the end of the drill string that breaks apart the rock being drilled. It contains jets through which the drilling fluid exits. Drill floor (#21) is the area on the rig where the tools are located to make the connections of the drill pipe, bottom hole assembly, tools and bit. It is considered the main area ...