enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   It indicates the diameter of smooth-walled hole that a male thread (e.g. on a bolt) will pass through easily to connect to an internally threaded component (e.g. a nut) on the other side. For example, an M6 screw has a nominal outer diameter of 6 millimetres and will therefore be a well-located, co-axial fit in a hole drilled to 6 mm diameter.

3. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

4. British Association screw threads - Wikipedia

   en.wikipedia.org/wiki/British_Association_screw...

   The pitch of 0BA is 1 mm and the pitch of each higher numbered thread is obtained by multiplying the pitch of the lower number by 0.9 so K-BA has a pitch of p = 0.9 K [4]: 12 rounded to two significant figures in mm. The major diameter is given by 6p 1.2, [4]: 12 rounded to two significant figures in mm and the hex head size (across the flats ...

5. Screw thread - Wikipedia

   en.wikipedia.org/wiki/Screw_thread

   The minor diameter is the lower extreme diameter of the thread. Major diameter minus minor diameter, divided by two, equals the height of the thread. The minor diameter of a nut is its inside diameter. The minor diameter of a bolt can be measured with go/no-go gauges or, directly, with an optical comparator.

6. Screw - Wikipedia

   en.wikipedia.org/wiki/Screw

   Thus, an M6 screw, which has a pitch of 1 mm, is made by threading a 6 mm shank, and the nut or threaded hole is made by tapping threads into a hole of 5 mm diameter (6 mm − 1 mm). Metric hexagon bolts, screws and nuts are specified, for example, in International Standards ISO 4014, ISO 4017, and ISO 4032. The following table lists the ...

7. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   To calculate the major diameter of "aught" size screws count the number of extra zeroes and multiply this number by 0.013 in and subtract from 0.060 in. For example, the major diameter of a #0000 screw is 0.060 in − (3 × 0.013 in) = 0.060 in − 0.039 in = 0.021 in.

8. Nut (hardware) - Wikipedia

   en.wikipedia.org/wiki/Nut_(hardware)

   Steel nuts are strong and great for construction, while stainless steel ones resist rust, perfect for outdoor use. Brass nuts, corrosion-resistant, find their place in electrical and plumbing work. Lock nuts, like nylon-insert or prevailing torque types, prevent loosening due to vibration or torque, catering to specific needs across industries.

9. ISO 965 - Wikipedia

   en.wikipedia.org/wiki/ISO_965

   ISO 965 (ISO general purpose metric screw thread—tolerances) is an International Organization for Standardization (ISO) standard for metric screw thread tolerances. [1] It specifies the basic profile for ISO general purpose metric screw threads (M) conforming to ISO 261. [2] The tolerance system refers to the basic profile in accordance with ...