enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. Wrench size - Wikipedia

    en.wikipedia.org/wiki/Wrench_size

    Sizes that may interchange, depending on the precision needed, include 2 mm (close to 5 ⁄ 64 inch (1.98 mm)), 4 mm (close to 5 ⁄ 32 inch (3.97 mm)) and 8 mm (close to 5 ⁄ 16 inch (7.94 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

  3. Millimetre - Wikipedia

    en.wikipedia.org/wiki/Millimetre

    Different lengths as in respect to the electromagnetic spectrum, measured by the metre and its derived scales.The microwave is between 1 meter to 1 millimeter.. The millimetre (international spelling; SI unit symbol mm) or millimeter (American spelling) is a unit of length in the International System of Units (SI), equal to one thousandth of a metre, which is the SI base unit of length.

  4. 6 mm caliber - Wikipedia

    en.wikipedia.org/wiki/6_mm_caliber

    2.1.24 in (6.2 mm) 2.2.25 in (6.5 mm) 2.3.264 in (6.6 mm) and up. 3 See also. ... Measurements are in millimeters then inches, i.e. mm (in). Pistol cartridges

  5. United States Mint coin sizes - Wikipedia

    en.wikipedia.org/wiki/United_States_Mint_coin_sizes

    2.268 g 1965–present Dime 17.9 mm 2.5 g 1796–1964 $2.50 Gold Quarter Eagle 18 mm 4.2 g 1796–1929 Small Cent 19.05 mm 2.5 g 1943 Small Cent 19.05 mm 3.11 g 1864-1982 Small Cent 19.05 mm 4.67 g 1856-1864 2.5 g 1982–present Three Dollar 20.5 mm 5.01 g 1853–1876 Nickel 21.21 mm 5 g 1866–present Nickel 21.21 mm 5 g 1942–1945 Twenty ...

  6. List of scale model sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_scale_model_sizes

    2.381 mm A few rockets and some fit-in-the-box aircraft are made to this size. 1:120: 0.1 in: 2.54 mm: Model railways (TT) Derived from the scale of 1 inch equals 10 feet.TT model railroad scale. Used in AD&D Battlesystem Skirmishes rules. Works with 15 mm miniatures where a 6 foot man would equal 15.24 mm 1:110: 2.771 mm

  7. Inch - Wikipedia

    en.wikipedia.org/wiki/Inch

    Subdivisions of an inch are typically written using dyadic fractions with odd number numerators; for example, two and three-eighths of an inch would be written as ⁠2 + 3 / 8 ⁠ ″ and not as 2.375″ nor as ⁠2 + 6 / 16 ⁠ ″. However, for engineering purposes fractions are commonly given to three or four places of decimals and have been ...

  8. List of examples of lengths - Wikipedia

    en.wikipedia.org/wiki/List_of_examples_of_lengths

    Lengths between 10 −2 and 10 −1 m (1 and 10 cm). 1 cm — 10 millimetres; 1 cm — 0.39 inches; 1 cm — edge of square of area 1 cm 2; 1 cm — edge of cube of volume 1 ml; 1 cm — approximate width of average fingernail; 1.5 cm — length of a very large mosquito; 2 cm — approximate width of an adult human finger; 2.54 cm — 1 inch

  9. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.