enow.com Web Search

  1. Ads

    related to: flex tube corrugated split tubing dimensions

Search results

  1. Results from the WOW.Com Content Network
  2. Tube (fluid conveyance) - Wikipedia

    en.wikipedia.org/wiki/Tube_(fluid_conveyance)

    Both pipe and tube imply a level of rigidity and permanence, whereas a hose is usually portable and flexible. A tube and pipe may be specified by standard pipe size designations, e.g., nominal pipe size, or by nominal outside or inside diameter and/or wall thickness. The actual dimensions of pipe are usually not the nominal dimensions: A 1-inch ...

  3. Corrugated stainless steel tubing - Wikipedia

    en.wikipedia.org/wiki/Corrugated_stainless_steel...

    CSST is not FAC (Flexible Appliance Connector) tubing. Presently, CSST and FAC tubing both use corrugated stainless steel tubing. In the past, FAC used corrugated brass tubing. However, FAC tubing is made only in lengths of 1 to 6 feet, FAC tubing is made with connectors on each end, and FAC tubing does not have a plastic sheath.

  4. Metal hose - Wikipedia

    en.wikipedia.org/wiki/Metal_hose

    Corrugated hoses are used as economical, flexible connecting elements that permit movement, thermal expansion and vibrations, and that can be used as filling hoses. The starting material is a seamless or longitudinally welded, thin-walled tube into which corrugations are introduced by mechanical or hydraulic means using special tools.

  5. Electrical conduit - Wikipedia

    en.wikipedia.org/wiki/Electrical_conduit

    Flexible metallic tubing (FMT; North America) is not the same as flexible metallic conduit (FMC) which is described in US National Electrical Code (NEC) Article 348. FMT is a raceway, but not a conduit and is described in a separate NEC Article 360. It only comes in 1/2" & 3/4" trade sizes, whereas FMC is sized 1/2" ~ 4" trade sizes.

  6. AN thread - Wikipedia

    en.wikipedia.org/wiki/AN_thread

    AN sizes range from -2 (dash two) to -32 in irregular steps, with each step equating to the OD (outside diameter) of the tubing in 1 ⁄ 16-inch increments. Therefore, a -8 AN size would be equal to 1 ⁄ 2-inch OD tube. However, this system does not specify the ID (inside diameter) of the tubing because the tube wall can vary in thickness.

  7. Copper tubing - Wikipedia

    en.wikipedia.org/wiki/Copper_tubing

    While pipe sizes in Australia are inch-based, they are classified by outside rather than inside diameter (e.g., a nominal 3 ⁄ 4 inch copper pipe in Australia has measured diameters of 0.750 inches outside and 0.638 inches inside, whereas a nominal 3 ⁄ 4 inch copper pipe in the U.S. and Canada has measured diameters of 0.875 inch outside and ...

  8. Nominal Pipe Size - Wikipedia

    en.wikipedia.org/wiki/Nominal_Pipe_Size

    Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

  9. Metal expansion joint - Wikipedia

    en.wikipedia.org/wiki/Metal_expansion_joint

    In 1920, he applied for a patent for the first so-called flexible metal tube expansion joint, German Reichspatent No. 367 185, from 29 July 1920. From a technical point of view, this precursor of today's expansion joints is a large, pressure-tight flexible metal hose with a defined, restricted freedom of movement.

  1. Ads

    related to: flex tube corrugated split tubing dimensions