enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. Barcol hardness test - Wikipedia

    en.wikipedia.org/wiki/Barcol_hardness_test

    Barcol hardness is measured on a scale from 0 to 100 with the typical range being between 50B and 90B. A measurement of 60B is roughly equivalent to a Shore hardness of 80D or a Rockwell hardness M100. [4] [6] As defined in ASTM D 2583 the scale divisions from 0-100 should each indicate a depth of 0.0076 mm or the equivalent 0.0003 inches. [7]

  3. Calculated Carbon Aromaticity Index - Wikipedia

    en.wikipedia.org/wiki/Calculated_Carbon_Aromati...

    As the name suggests, CCAI is a calculation based on the density and viscosity of a given fuel. The formula is rather complex but in general, the higher the CCAI, the poorer the ignition quality of the fuel is considered to be. Once the CCAI goes above 860, it is an indication that some combustion problems may occur.

  4. SAE J300 - Wikipedia

    en.wikipedia.org/wiki/SAE_J300

    The longer it takes, the higher the viscosity and thus the higher the SAE code. Larger numbers are thicker. J300 specifies a viscosity range for each non-winter grade, with higher grade numbers corresponding to higher viscosities. In addition, a minimum viscosity measured at a high temperature and high-shear rate (HTHS, ASTM D4683) is also ...

  5. Cetane index - Wikipedia

    en.wikipedia.org/wiki/Cetane_index

    The cetane index is calculated based on the fuel's density and distillation range (ASTM D86). There are two methods used, ASTM D976 and D4737. There are two methods used, ASTM D976 and D4737. The older D976, or "two-variable equation" is outdated and should no longer be used for cetane number estimation.

  6. Pitting resistance equivalent number - Wikipedia

    en.wikipedia.org/wiki/Pitting_Resistance...

    Pitting resistance equivalent number (PREN) is a predictive measurement of a stainless steel's resistance to localized pitting corrosion based on its chemical composition. In general: the higher PREN-value, the more resistant is the stainless steel to localized pitting corrosion by chloride .

  7. Janka hardness test - Wikipedia

    en.wikipedia.org/wiki/Janka_hardness_test

    The Janka hardness test results tabulated below followed ASTM D 1037-12 testing methods. Lumber stocks tested range from 1" to 2" (25–50 mm) thick. The tabulated Janka hardness numbers are an average. There is a standard deviation associated with each species, but these values are not given. [citation needed] No testing was done on actual ...

  8. Los Angeles abrasion test - Wikipedia

    en.wikipedia.org/wiki/Los_Angeles_abrasion_test

    In the 1930s, national studies demonstrated the Deval test did not correlate with the service record of sampled rock altogether, while an LA loss rating of less than 40% was a reliable indicator of quality. [9] The federal standard for LA abrasion testing was formally adopted by the ASTM in 1937. [10]

  9. List of body armor performance standards - Wikipedia

    en.wikipedia.org/wiki/List_of_body_armor...

    The VPAM scale as of 2009 runs from 1 to 14, with 1-5 being soft armor, and 6-14 being hard armor. [1] Tested armor must withstand three hits, spaced 120 mm (4.7 inches) apart, of the designated test threat with no more than 25 mm (0.98 inches) of back-face deformation in order to pass.

  1. Related searches astm d5261 equivalent rating range lookup calculator table

    astm d5261 equivalent rating range lookup calculator table chartvlookup range lookup
    excel range lookup