enow.com Web Search

  1. Ad

    related to: cable wood chop low to high point distance in mm x 1 25 x 35 mm long stud

Search results

  1. Results from the WOW.Com Content Network
  2. Cable length - Wikipedia

    en.wikipedia.org/wiki/Cable_length

    A cable's length (often "cable length" or just "cable") is simply the standard length in which cables came, which by 1555 had settled to around 100 fathoms (600 ft; 180 m) or 1 ⁄ 10 nautical mile (0.19 km; 0.12 mi). [1] Traditionally rope is made on long ropewalks, the length of which determines the maximum length of rope it is possible to make.

  3. Cable railing - Wikipedia

    en.wikipedia.org/wiki/Cable_railing

    The most common cable construction is 1x19 type construction strand, which is 19 cables twisted in a single bundle, whereas for example, 7x7 would be 7 cable bundles of 7 cables twisted. This type of stainless strand is designed to have limited stretch, as compared to galvanized, [6] making it a good long term cable railing solution. It has ...

  4. Lumber - Wikipedia

    en.wikipedia.org/wiki/Lumber

    Re-sawing is the splitting of 1-to-12-inch (25–305 mm) hardwood or softwood lumber into two or more thinner pieces of full-length boards. For example, splitting a 10-foot-long (3.0 m) 2×4 (1 + 1 ⁄ 2 by 3 + 1 ⁄ 2 in or 38 by 89 mm) into two 1×4s (3 ⁄ 4 by 3 + 1 ⁄ 2 in or 19 by 89 mm) of the same length is considered re-sawing.

  5. Railroad tie - Wikipedia

    en.wikipedia.org/wiki/Railroad_tie

    Of high importance to railroad companies is the fact that steel ties are more economical to install in new construction than creosote-treated wood ties and concrete ties. Steel ties are utilized in nearly all sectors of the worldwide railroad systems including heavy-haul, class 1s, regional, shortlines, mining, electrified passenger lines (OHLE ...

  6. Engineering tolerance - Wikipedia

    en.wikipedia.org/wiki/Engineering_tolerance

    For example, if a shaft with a nominal diameter of 10 mm is to have a sliding fit within a hole, the shaft might be specified with a tolerance range from 9.964 to 10 mm (i.e., a zero fundamental deviation, but a lower deviation of 0.036 mm) and the hole might be specified with a tolerance range from 10.04 mm to 10.076 mm (0.04 mm fundamental ...

  7. Woodchopping - Wikipedia

    en.wikipedia.org/wiki/Woodchopping

    Woodchopping (also spelled wood-chopping or wood chopping), called woodchop for short, is a sport that has been around for hundreds of years in several cultures. In woodchopping competitions, skilled contestants attempt to be the first to cut or saw through a log or other block of wood. It is often held at state fairs and agricultural shows.

  8. Cutting board - Wikipedia

    en.wikipedia.org/wiki/Cutting_board

    A kitchen knife on a wooden cutting board. A cutting board (or chopping board) is a durable board on which to place material for cutting.The kitchen cutting board is commonly used in preparing food; other types exist for cutting raw materials such as leather or plastic.

  9. Coaxial cable - Wikipedia

    en.wikipedia.org/wiki/Coaxial_cable

    The best coaxial cable impedances were experimentally determined at Bell Laboratories in 1929 to be 77 Ω for low-attenuation, 60 Ω for high-voltage, and 30 Ω for high-power. For a coaxial cable with air dielectric and a shield of a given inner diameter, the attenuation is minimized by choosing the diameter of the inner conductor to give a ...

  1. Ad

    related to: cable wood chop low to high point distance in mm x 1 25 x 35 mm long stud